3D Systems ProJet 2500 Скачать руководство пользователя | Manualshive

Страница: 48 / 53

background image

3D Systems, Inc.

11

BASIC REGULATIONS

3D Systems has tested this printer to electromagnetic emission and immunity standards . These standards are designed to mitigate

interference caused or received by this printer in a typical office environment.

United States

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules . These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment . This equipment generates, uses, and can radiate radio frequency energy . If it is not installed and used
in accordance with these instructions, it may cause harmful interference to radio communications . Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own
expense .

Changes or modifications to this equipment not approved by 3D Systems can void the authority of the user to operate this equipment.

Canada

Ce dispositif est conforme aÌ la norme CNR-210 d’Industrie Canada applicable aux appareils radio exempts de licence . Son

fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage preìjudiciable, et (2) ce

dispositif doit accepter tout brouillage rec?u, y compris un brouillage susceptible de provoquer un fonctionnement indeìsirable.

This Class A digital apparatus complies with Canadian ICES-003 .

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada .

European Union

CAUTION: This is a Class A product . In a domestic environment, this product can cause radio interference in which
case the user could be required to take adequate measures .

In order to allow the equipment to operate in close proximity to Industrial, Scientific and Medical (ISM) equipment, the external radiation

from the ISM equipment may have to be limited or special mitigation measures taken .

Changes or modifications to this equipment not approved by 3D Systems can void the authority of the user to operate this equipment.

43

«
...
46
47
48
49
50
...
»

Содержание ProJet 2500






















































Отзывы:

Нет отзывов

Похожие инструкции для ProJet 2500

Pixma MG2400 Series

Бренд: Canon Страницы: 2

Бренд: 3DMakerWorld Страницы: 85

Бренд: Oki Страницы: 116

Бренд: Oki Страницы: 52

Бренд: Oki Страницы: 331

Бренд: Oki Страницы: 36

C5800Ldn Series

Бренд: Oki Страницы: 143

Бренд: Oki Страницы: 101

Бренд: Oki Страницы: 36

Бренд: Oki Страницы: 282

Бренд: Oki Страницы: 269

Бренд: Oki Страницы: 3

Бренд: Oki Страницы: 6

Бренд: Oki Страницы: 72

Бренд: Oki Страницы: 75

Бренд: Oki Страницы: 250

Бренд: µ-Dimension Страницы: 74

Бренд: Printek Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды