3D Systems ProJet 2500 Скачать руководство пользователя

Страница: 17 / 53

PRINTING AREA

The actual area that you can print a job consists of the length x width
plus the maximum height of a job . This diagram illustrates exactly
what the maximum build area is for the ProJet 2500 .

3D PRINTER SYSTEM COMPONENTS

For 3D printer system requirements, consult the

Facility

Requirements Guide

288mm

11.34in

212mm

8.35in

144mm

5.67in

Need updated diagram from Wilsonville

User Interface

The User Interface consists of a tablet built into the top of the printer

to the right. There are five main screens that contain sub menus that

allow the user to do a variety of things through the tablet. These five

screens and their menus are:

1 .

Status Screen

•

Current Layer Info

•

Print Sender

•

Printer State

•

Waste Bag Usage

2 .

Prints Screen

•

Opens Print Queue for the Printer

3 .

Materials Screen

•

Material Status

•

Part Message

•

Support Message

4 .

Tools Screen

•

Diagnostics

•

Material Change Wizard

•

Printer Info

•

Access Platform

•

Play

•

Refresh Job Queue

•

Email Notification

•

Printer Usage

•

Printer Shutdown

5 .

Settings Screen

•

Admin Settings

•

Email Alerts

•

Alert Settings

•

Network Settings

•

Printer Connection

These are the only things that can be done through the UI . All other
operations must be done through a computer/laptop using the
3D

SPRINT

software . For complete information on using

SPRINT

the

Help

(6) file can be accessed through the icon in

the software .

Содержание ProJet 2500





















































Результаты поиска

Содержание ProJet 2500

Отзывы:

Похожие инструкции для ProJet 2500

Бренды по названию

Популярные бренды

3D Systems ProJet 2500, Руководство пользователя

Результаты поиска

Содержание ProJet 2500

Отзывы:

Похожие инструкции для ProJet 2500

Бренды по названию

Популярные бренды