ZURN Aquaflush Z6000 Installation, Operation, Maintenance And Parts Manual Download Page 28

Page: 28 / 89

AquaSense Batter

owered Flush

alves/Retrofit Kits

E-Z FLUSH COMPONENTS

E-Z FLUSH

BATTERY

COMPARTMENT WRENCH

GASKET

4 “C” ALKALINE

BATTERIES

WRENCH

The E-Z Flush

™

sends out a continuous infrared beam that is reflected back by the presence of a person in front of the urinal or toilet.

The technology differentiates between someone walking past the unit or actually using the fixture. E-Z Flush models ZERK-CP and
ZERK-CPM retrofit Zurn and Sloan valves. For Delaney valves, order model ZERK-CP-LY or ZERK-CPM-LY.

DESCRIPTION

User Approaches

E-Z Flush

Senses User

E-Z Flush Flushes

When User Leaves

Collar Nut

Collar Gasket

Shut off water supply at stop.

A –

Using the supplied wrench, loosen
handle nut.

B –

Remove handle from flush valve.

Note:

A small amount of water may

drip from the port.

C –

Place gasket into nut and attach
the E-Z Flush unit where the handle
was removed.

D –

Tighten nut with supplied wrench.

Note:

Save handle in the event

you wish to reuse for service of
E-Z Flush.

INSTALLATION

STEP A

STEP B

STEP C

STEP D

Page 2 FV2001

Summary of Contents for Aquaflush Z6000


























































































Search results

Summary of Contents for Aquaflush Z6000

Reviews:

Related manuals for Aquaflush Z6000

Brands by name

Popular brands

ZURN Aquaflush Z6000, Installation, Operation, Maintenance And Parts Manual

Search results

Summary of Contents for Aquaflush Z6000

Reviews:

Related manuals for Aquaflush Z6000

Brands by name

Popular brands