Zte ZXSDR R8854 Hardware Installation Download Page 69

Page: 69 / 72

Chapter 5 Cable Installation

When you make the connector of the DC power cable, cut off the exposed shielded

layer after stripping off the cable end and bind the connector with a heat shrink tube

or insulating tape.

13. Label the power cable at both ends.

– End of Steps –

5.6 Installing an Optical Fiber Cable

This procedure describes how to install an optical fiber cable.

Steps

Installing Optical Fiber

Open the crimping clip at the left side of the maintenance window, see

Figure 5-15

Figure 5-15 Open the crimping clip

Remove the cable tie at one end of the corrugated pipe marked as "RRU" by using the

diagonal pliers.

Remove the white dust cap of the optical cable connector, see

Figure 5-16

Figure 5-16 Remove the white dust cap

White dust cap

5-15

SJ-20160405141455-003|2018-01-03 (R1.3)

ZTE Proprietary and Confidential

Summary of Contents for ZXSDR R8854









































































Search results

Summary of Contents for ZXSDR R8854

Reviews:

Related manuals for ZXSDR R8854

Brands by name

Popular brands

Zte ZXSDR R8854, Hardware Installation

Search results

Summary of Contents for ZXSDR R8854

Reviews:

Related manuals for ZXSDR R8854

Brands by name

Popular brands