Zte ZXSDR R8854 Hardware Installation Download

Page: 17 / 72

Chapter 3

Unpacking and Inspection

Counting Goods

Verify that the packaging boxes are intact. If any damage is found, contact the

transport company immediately.

Unpack the boxes and verify that the goods are consistent with the inspection

checklist.

Verify that the chassis is in good condition without scratches, peeling paint, blisters,

or stains.

Verify that the accessories required for the installation are correct and complete.

Equipment Handover

After the examination of goods, the engineering supervisor and the operator's

representative should sign the

Unpacking Acceptance Report

. The

Unpacking Acceptance

Report

is made in duplicate, and kept by both parties. The engineering supervisor must

send the

Unpacking Acceptance Report

back to the representative office within seven

days for archiving.

3-1

SJ-20160405141455-003|2018-01-03 (R1.3)

ZTE Proprietary and Confidential

Summary of Contents for ZXSDR R8854









































































Search results

Summary of Contents for ZXSDR R8854

Reviews:

Related manuals for ZXSDR R8854

Brands by name

Popular brands

Zte ZXSDR R8854, Hardware Installation

Search results

Summary of Contents for ZXSDR R8854

Reviews:

Related manuals for ZXSDR R8854

Brands by name

Popular brands