manualshive.com logo in svg

Zte ZXSDR R8854, Hardware Installation

Share
Download
Zte ZXSDR R8854 Hardware Installation Download Page 9

Chapter 2

Installation Preparations

Before installing the ZXSDR R8854, installation engineers should check the installation

environment and deliver an

Environment Acceptance Report

.

Installation parts, tools, and instruments should be available before installation.

Caution!

The ZXSDR R8854 must be powered on within 24 hours after it is unpacked.

The power-off duration of the ZXSDR R8854 must not be greater than 24 hours during

maintenance.

Table of Contents

Precautions for Device Transport ...............................................................................2-1

Precautions for Device Hoisting..................................................................................2-1

Installation Precautions ..............................................................................................2-4

Instruments and Meters List .......................................................................................2-6

Installation Space Requirement ..................................................................................2-7

2.1 Precautions for Device Transport

l

A device must be transported with the outer packing container to protect the device

from scratches.

l

After the packing container is removed on site, the device must be protected when

you move or store it. For example, when a device is stored temporarily, cushioning

materials must be put under the bottom of the device to avoid direct contact with the

ground and surrounding objects.

l

When you transport a device, cushioning materials such as foamed plastic and

paperboard must be used to protect the device from scratches. When you lift a

device up, the device must be dragged properly to avoid collision with other objects.

2.2 Precautions for Device Hoisting

The information provided is used for reference when it is necessary to hoist the

RRU

.

1.

Installer A on the tower secures the fixed pulley to the tower, and passes the hoisting

rope through the fixed pulley down to the ground, see

Figure 2-1

.

2-1

SJ-20160405141455-003|2018-01-03 (R1.3)

ZTE Proprietary and Confidential

Summary of Contents for ZXSDR R8854









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands