Zte ZXSDR R8854 Hardware Installation Download

Page: 68 / 72

ZXSDR R8854 Hardware Installation

Figure 5-13 Connecting the Power Cable to the Grounding Kit

Note:

When a grounding kit is used, the angle between the grounding cable and the power

cable cannot be upward or be greater than 15 degrees. If the grounding kit is away from

the feeder window, the grounding cable should be routed toward the feeder window

along the downward direction of the power cable.

Connecting the Power cable of the Power Supply Equipment

12. Use a tubular terminal to make the connector of the AC power cable at the BBU side,

and then connect the AC power cable to the DC output port of the DCPD, see

Figure

5-14

Figure 5-14 Connecting the Power Cable to the DCPD

5-14

SJ-20160405141455-003|2018-01-03 (R1.3)

ZTE Proprietary and Confidential

Summary of Contents for ZXSDR R8854









































































Search results

Summary of Contents for ZXSDR R8854

Reviews:

Related manuals for ZXSDR R8854

Brands by name

Popular brands

Zte ZXSDR R8854, Hardware Installation

Search results

Summary of Contents for ZXSDR R8854

Reviews:

Related manuals for ZXSDR R8854

Brands by name

Popular brands