Zte ZXSDR R8854 Hardware Installation Download | Manualshive

Page: 29 / 72

background image

Chapter 4 RRU Installation

Figure 4-13 Securing the RRU

– End of Steps –

4.2 Installing a Single RRU on a Pole

A single RRU can be installed on a round pole (φ40–120 mm), a channel steel pole

(φ60–100 mm), or an angle steel pole (φ63–100 mm).

The following description and procedure are based on round pole-mounted installation.

Figure 4-14

and

Figure 4-15

show channel steel pole-mounted installation and angle steel

pole-mounted installation respectively.

4-11

SJ-20160405141455-003|2018-01-03 (R1.3)

ZTE Proprietary and Confidential

«
...
27
28
29
30
31
...
»

Summary of Contents for ZXSDR R8854









































































Reviews:

No comments

Related manuals for ZXSDR R8854

Brand: Rapid Pages: 2

Brand: JBL Pages: 29

Brand: Tait Pages: 108

Brand: Q-Mac Pages: 62

Brand: Akai Pages: 12

Brand: Tekcom Industries Pages: 14

Brand: Konig Pages: 21

Brand: Brigmton Pages: 10

Brand: Wintec Pages: 16

Brand: Topcom Pages: 4

Brand: MAJORITY Pages: 16

Brand: THOMSON Pages: 168

Brand: Uniden Pages: 104

Brand: SOUNDMASTER Pages: 4

Brand: Radio Shack Pages: 24

Brand: X4-TECH Pages: 48

Brand: Audizio Pages: 36

Brand: Denver Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands