background image

Page 9

Page 8

MagnaPool™   |   Installation Manual

Section 4. Install Controller

The controller should be located at or near the 

equipment pad, at least 3.5 metres or more away 

from the inside wall of the pool/spa, 1.5 metres 

off the ground, and within 2 meters of the cell. All 

national, state, and local codes are applicable. 

4.1

Mount the Bracket

1. Determine the controller location.

2. Use the enclosed bracket to mark the 

mounting surface through the screw holes.

3. Drill surface with 7 mm bit.

4. Install the included wall anchors.

5. Hang bracket using the included screws.

6. Hang the controller on the wall bracket and 

slide to the right to secure in place.

Figure 6.

Controller Mount

4.2

Install temperature sensor

The temperature sensor must be installed 

upstream from any heating equipment, 

see Figure 3 

and Figure 4.

 The sensor will need to be placed into 

the plumbing system at any suitable position after 

the filter pump and before any heating equipment.
1. Drill a Ø9 mm hole in the top of the pipe.

2. Ensure the o-ring is properly seated on the 

sensor body.

3. Secure the sensor and o-ring with the screw 

clamp provided. DO NOT OVERTIGHTEN.

Figure 7.

Install Temperature Sensor

4.3

Electrical Connections

 WARNING

FOR YOUR SAFETY: 

 This product must be 

serviced by a professional pool/spa service 

technician as described on the front cover of this 

manual. The procedures in this manual must be 

followed exactly. Failure to follow warning notices 

and instructions may result in property damage, 

serious injury, or death. Improper installation and/or 

operation will void the warranty. 

The controller must be permanently powered by 

connection to a 30 mA residential circuit breaker.
The controller can be used to connect and control 

multiple devices see Table 5 for a summary of functions.

4.3.1

Remove Lower Cover

1. Unplug power supply from mains.

2. Remove the external cover.

3. Remove the 2 screws from the lower housing.

4. Remove the lower housing by pulling down 

then out see Figure 8.

Figure 8.

Remove Controller Lower Cover

Ø9 MM

Summary of Contents for MagnaPool































Reviews: