![background image](http://html1.mh-extra.com/html/zodiac/magnapool/magnapool_installation-manual_3986087024.webp)
Page 25
Page 24
MagnaPool™ | Installation Manual
The “P” symbol is displayed in the upper right-hand
corner of the LCD display on the home screen if a
valid filter pump and hydroxinator program has been
set.
23:04 ON
T
23:04 ON
P
8.7.6
AUX/Lights Programming
1. Press
.
2. Use
to select “Programming”
then press .
3. Use
to select “AUX/Lights” then press .
4. Use
to select “AUX 1 Timer” or “AUX 2
Timer” then press .
5. Use
to select the hour for the AUX on
time then press .
6. Use
to select the minutes for the AUX on
time then press .
7. Use
to select the hour for the AUX off
time then press .
8. Use
to select the minutes for the AUX off
time then press .
9. Press
to exit.
<
-AUX/LIGHTS
-PROGRAMMING
-LOW MODE
-SLAVE MODE
-REVERSING
-HELP MENU
-LANGUAGE
MAIN MENU
<
AUX/LIGHTS
-ASSIGN LIGHTS
-AUX 2
-AUX 1
<
AUX 2
-OFF
-ON
-SET TIMERS
<
AUX TIMER
-AUX 2 ON
-AUX 2 OFF
12:30
04:30
8.8
Reversing
CAUTION
Adjusting your cell reversal times will result in voiding
of warranty. You must consult with Zodiac on 1300 763
021 or your local pool care professional before making
any adjustments.
The hydroxinator uses a smart polarity reversal
system. Periodic polarity reversal will prevent
scaling of the cell plates. The time between each
reversal is factory set at 5 hours. This setting
is optimal for most water conditions. However,
Depending on the calcium hardness of the water,
you may need to adjust the reversal time. More
calcium in the water will require less time between
reversals. Water with less calcium can be given
more time between reversals. Shorter reversal
times will cause more wear of your cell plates. The
polarity reversal interval can be adjusted from 2 to
8 hours in 1-hour steps.
1. Press
.
2. Use
to select “Reversing” then press .
3. Use
to select set hours then press .
4. Press
to exit.
<
-REVERSING
-HELP MENU
-LANGUAGE
MAIN MENU
<
INVERSION PERIOD
5 HOURS
REVERSING TIME
During reversal, hydroxination is stopped for a few
minutes. No message is displayed on the screen.
Normal operation will resume after the reversal.
8.9
Slave Mode
Slave mode relinquishes control of the
hydroxination function to an external controller.
The controller must be connected to the “Slave”
connection point in the low voltage raceway see
Table 5 and Figure 10 for wiring details.
Boost and Low modes will remain operational from
the controller. However, HYDROX programs will be
deactivated. Hydroxination output will be maintained at
100%.
1. Connect the external controller at the slave
connection point in the ow voltage raceway
see Table 5 and Figure 10 for wiring details.
2. Press
.
3. Use
to select “Slave Mode”
then press .
4. Use
to select “YES” or “NO” then press .
5. Press
to exit.
<
-SLAVE MODE
-REVERSING
-HELP MENU
-LANGUAGE
MAIN MENU
<
SLAVE MODE
ACTIVATE?
- YES
- NO
<
23:04 ON
SLAVE MODE
<
23:04 OFF
SLAVE MODE
Slave mode only controls the hydroxination.
Filtration pump, AUX, lights and other functions are
still valid.
Pressing
will take priority over Slave mode.
If a Dual Link module is installed, the ORP function
is overridden by the slave mode. The pH regulation
is still valid.
LOW / COVER / BOOST modes takes priority over
Slave mode