Zimmer MFS02-S-KHC-IL Installation And Operating Instructions Manual Download Page 32

Page: 32 / 34

Zimmer GmbH • Im Salmenkopf 5 •



77866 Rheinau, Germany •



+49 7844 9138 0 • www.zimmer-group.com

EN / 2023-07-07

DDOC01932 / -

INSTALLATION AND OPERATING INSTRUCTIONS:

MFS02-S-KHC-IL

Device specific
Index

dec (hex)

Name

Format

(Offset)

Length

Access

Default

Value

Value / Range

Remark [Unit]

4367 (0x110F)

DD - Reset device diagnostics

parameters

UInt

8 Bit

1 = Reset operating hours

2 = Reset power cycles

255 = Reset all device

diagnostics

parameters

DD - reset the device diagnostics

parameters

4368 (0x1110)

DD - Alert source

Record

2 Byte

Set the alert source of the device diagnosis data

1 (0x01)

Operating hours alert source

Bit (8)

8 Bit

0 = Total

1 = Since Last Reset

2 = Since Startup

2 (0x02)

Power cycles alert source

Bit (0)

8 Bit

0 = Total

1 = Since Last Reset

4369 (0x1111)

DD - Alert limit

Record

8 Byte

Set the limits of the device diagnosis alerts

1 (0x01)

Operating hours limit

Bit (32)

32 Bit

876000

0...876000

[h]

2 (0x02)

Power cycles limit

Bit (0)

32 Bit

1000000

4370 (0x1112)

DD - Alert flags

Record

1 Byte

Get the device diagnosis alerts

1 (0x01)

Operating hours alert

Bit (1)

1 Bit

true = Alert occurred

false = Alert did not occur

2 (0x02)

Power cycles alert

Bit (0)

1 Bit

true = Alert occurred

false = Alert did not occur

4372 (0x1114)

Actuator travel [x10μm]

UInt

16 Bit

[x10μm]

4374 (0x1116)

Total actuator travel [sum m]

UInt

32 Bit

[m]

4375 (0x1117)

Average actuator velocity

[m/s]

Record

8 Byte

1 (0x01)

Extend (positive direction)

Bit (32)

4 Byte

Format = Float [m/s]

2 (0x02)

Retract (negative direction)

Bit (0)

4 Byte

Format = Float [m/s]

4379 (0x111B)

Actuator travel time [ms]

Record

8 Byte

1 (0x01)

Extend (positive direction)

Bit (32)

4 Byte

Format = Float [m/s]

2 (0x02)

Retract (negative direction)

Bit (0)

4 Byte

Format = Float [m/s]

4380 (0x111C)

Cycle time [ms]

Float

8 Byte

[ms]

4381 (0x111D)

Dwell time [ms]

Record

4 Byte

1 (0x01)

Start position

Bit (32)

4 Byte

Format = Float [m/s]

2 (0x02)

Start position

Bit (0)

4 Byte

Format = Float [m/s]

4382 (0x111E)

Cycle count [sum]

UInt

32 Bit

4398 (0x112E)

Reset actuator diagnostics

parameters

UInt

8 Bit

1 = Reset total actuator travel

2 = Reset actuator cycles

255 = Reset all actuator

diagnostics

parameters

DD - reset the device diagnostics

parameters

4399 (0x112F)

Actuator alert limits

Record

16 Byte

Set the limits of the actuator alerts

1 (0x01)

Total actuator travel limit

Bit (96)

32 Bit

100000

[m]

2 (0x02)

Min. cycle time limit

Bit (64)

4 Byte

Format = Float

[ms]

3 (0x03)

Max. cycle time limit

Bit (32)

4 Byte

86400000

Format = Float

[ms]

4 (0x04)

Cycle count limit

Bit (0)

32 Bit

1000000

4400 (0x1130)

Actuator alerts

Record

2 Byte

Get the actuator alerts

1 (0x01)

Total actuator travel alert

Bit (10)

1 Bit

true = Alert occurred

false = Alert did not occur

2 (0x02)

Min. cycle time alert

Bit (9)

1 Bit

true = Alert occurred

false = Alert did not occur

3 (0x03)

Max. cycle time alert

Bit (8)

1 Bit

true = Alert occurred

false = Alert did not occur

4 (0x04)

Cycle count alert

Bit (7)

1 Bit

true = Alert occurred

false = Alert did not occur

4602 (0x11FA)

Current field strength [mT]

Record

8 Byte

Magnetic field strength of magnetic elements

1 (0x01)

Current1

Bit (32)

4 Byte

Magnetic field strength of magnetic element 1. Format = Float [mT]

2 (0x02)

Current2

Bit (0)

4 Byte

Magnetic field strength of magnetic element 2. Format = Float [mT]

4604 (0x11FC)

Peak field strength [mT]

Record

8 Byte

1 (0x01)

Current1

Bit (32)

4 Byte

Magnetic field strength of magnetic element 1. Format = Float [mT]

2 (0x02)

Current2

Bit (0)

4 Byte

Magnetic field strength of magnetic element 2. Format = Float [mT]

4842 (0x12EA)

Alert settings

Record

8 Byte

1 ro = read only, wo = write only, rw = read/write

2 COM values specify the bitrate (see IO-Link specification): COM1 (4,8 kbit/s), COM2 (38,4 kbit/s), COM3 (230,4 kbit/s)

Summary of Contents for MFS02-S-KHC-IL



































Search results

Summary of Contents for MFS02-S-KHC-IL

Reviews:

Related manuals for MFS02-S-KHC-IL

Brands by name

Popular brands

Zimmer MFS02-S-KHC-IL, Installation And Operating Instructions Manual

Search results

Summary of Contents for MFS02-S-KHC-IL

Reviews:

Related manuals for MFS02-S-KHC-IL

Brands by name

Popular brands