Zimmer MFS02-S-KHC-IL Installation And Operating Instructions Manual Download Page 15

Page: 15 / 34

Zimmer GmbH • Im Salmenkopf 5 •



77866 Rheinau, Germany •



+49 7844 9138 0 • www.zimmer-group.com

DDOC01932 / -

INSTALLATION AND OPERATING INSTRUCTIONS:

MFS02-S-KHC-IL

EN / 2023-07-07

11.4.2 Resetting settings

•

The

Device Reset

command only deletes the volatile parameters. The command can be executed via

Index 2 (0x02)/

System Command, Value 128

Index

Name

Volatile/Non-volatile

4372 (0x1114)

Actuator travel

Volatile

4380 (0x111C)

Cycle time

Volatile

4381 (0x111D)

Dwell time

Volatile

4379 (0x111B)

Actuator travel time

Volatile

4375 (0x1117)

Average actuator velocity

Volatile

4602 (0x11FA)

Current field strength

Volatile

4604 (0x111FC)

Peak field strength

Volatile

4374 (0x1116)

Total actuator travel

Non-volatile

4382 (0x111E)

Cycle count

Non-volatile

Qint. 1-8 SP1 / SP2

Qint. 1-8 Configuration

Non-volatile

•

The

Restore Factory Settings

command resets all settings made back to the default settings. The command can be

executed via

Index 2 (0x02)/System Command, Value 130

. The following indices remain unchanged:

•

4356 (0x1104)/Operating hours

•

4357 (0x1105)/Power cycles, Subindex 1 (0x01)/Total

•

4382 (0x111E)/Cycle count

•

4374 (0x1116)/Total actuator travel

•

The command

Reset Diagnostic Parameters

can be executed via

Index 2 (0x02)/System Command, Value 228

. The

following indices are reset:

•

4356 (0x1104)/Operating Hours, Subindex 2 (0x02)/Since last reset

•

4357 (0x1105)/Power cycles, Subindex 2 (0x02)/Since last reset

•

4382 (0x111E)/Cycle count

•

4374 (0x1116)/Total actuator travel, Index 2 (0x02)/System Command, Value 228

•

The command

Reset all present alerts

resets all alert notifications. The command can be executed via

Index 2 (0x02)/

System Command, Value 229

•

The command

Reset operating hours counter

can be executed via

Index 2 (0x02)/System Command, Value 228

. The

following indices are reset:

•

4356 (0x1104)/Operating hours, Subindex 2 (0x02)/Since last reset

•

The command

Reset power cycles counter

can be executed via

Index 2 (0x02)/System Command, Value 228

. The

following indices are reset:

•

4357 (0x1105)/Power cycles

•

The command

Reset actuator cycles counter

can be executed via

Index 4398 (0x112E)/Reset actuator diagnostics

parameters, Value 2

. The following indices are reset:

•

4382 (0x111E)/Cycle Count

•

The command

Reset total actuator travel

can be executed via

Index 4398 (0x112E)/Reset actuator diagnostics

parameters, Value 1

. The following indices are reset:

•

4374 (0x1116)/Total actuator travel

•

The command

Application reset

can be executed via

Index 2 (0x02)/System Command, Value 129

. This command can

reset the same indices as the command

Restore factory settings

; however, this command has no effect on the identifi-

cation parameters

Index 24, 25, 26

and

•

The command

Reset trained algorithm parameter

can be executed via

Index 2 (0x02)/System Command, Value 192

This command does not reset any diagnostic data or settings, but rather only the measured values of the algorithm. It is

recommended to use this command if the product will be mounted to a different drive. Only two complete piston strokes

are then required for the teach-in process.

Summary of Contents for MFS02-S-KHC-IL



































Search results

Summary of Contents for MFS02-S-KHC-IL

Reviews:

Related manuals for MFS02-S-KHC-IL

Brands by name

Popular brands

Zimmer MFS02-S-KHC-IL, Installation And Operating Instructions Manual

Search results

Summary of Contents for MFS02-S-KHC-IL

Reviews:

Related manuals for MFS02-S-KHC-IL

Brands by name

Popular brands