Zetor MAJOR HS Operator'S Manual Download

Page: 34 / 140

Cab heating registers

Cab air condition

If the air conditioning is in operation, adjust the vents (2) to the required angle so that no

direct blowing of people in the cabin occur (risk of diseases because of intensive cooling of body
parts).

The air conditioning can be operated only when both switches (1) and (2) are on!

Proper function of the heating and air-condition system

It is necessary to create surplus pressure in the cabin for proper function of the heating or air-condition. We

therefore recommend you to close all the windows and doors and tilting cover of the cabin.

Switch box

The heating vents are located on the upper and lateral
side of the steering column.

MHS16N049

The air conditioning system is controlled with the switches
located on the panel in the cabin roof (A).

Switching on and off of the function of the air conditioning

system is performed by switching the switch with the

snowflake symbol (1).

Activate the air conditioning system by pressing the switch
(the snowflake symbol glows).

Deactivate the air conditioning system by pressing the

switch again (the snowflake symbol stops glowing).

Revolutions of the double-speed fan of the air conditioning

system are adjusted with the switch (2).

The air conditioning vents (3) are located in the roof of the
cab (B).

Note:

The switch (1) must be switched and the fan of the

air conditioning system must be activated with the switch

(2) to enable functioning of the air conditioning system.

MHS16N102

The switch box is located on the right side of the steering

column.

MHS16N008

ACQUAINTANCE WITH THE TRACTOR

Summary of Contents for MAJOR HS













































































































































Search results

Summary of Contents for MAJOR HS

Reviews:

Related manuals for MAJOR HS

Brands by name

Popular brands

Zetor MAJOR HS, Operator'S Manual

Search results

Summary of Contents for MAJOR HS

Reviews:

Related manuals for MAJOR HS

Brands by name

Popular brands