Zelmer Syrius, User Manual

Page: 40 / 42

42
B
Appliance elements
1 Electrobrush socket
2 ON/OFF button
3 Handle
4 Cord rewind button
5 Combination brush fastening
6 Accessory compartment cover
7 Plug and cord
8 Outlet filter cover
9 Filter wear indicator
10 Power increase
11 Suction power level indicator
12 Power decrease button -
13 Infrared receiver (type 1600.3)
14 Dust bag full indicator
15 Front cover fastening
16 Infrared transmitter (type 1600.3)
17 STANDBY mode button (type 1600.3)
18 Suction hose (type 1600.0)
19 Suction hose with remote power control (type 1600.3)
20 Outlet filter HEPA H13 (type 1600.0 HQ, 1600.3 HT,
1600.3 HQ) (installed in the vacuum cleaner)
21 Outlet filter HEPA H11 (type 1600.0 SP, 1600.0 ST)
(installed in the vacuum cleaner)
22 Inlet filter (installed in the vacuum cleaner)
23 SAFBAG dust bag (2 pieces)
24 Telescopic suction tube
25 Small brush
26 Crevice nozzle
27 Small nozzle
28 Turbobrush (type 1600.0 ST, 1600.3 HT)
29 Electrobrush (type 1600.0 HQ, 1600.3 HQ)
30 Combination brush. The vacuum cleaner is equipped
with only one type of combination brush (A or B)
A Switchable combination brush
B
Combination brush with a small item separator
31 Parquet brush “BNB”
Is used to clean and polish hard, scratch sensitive surfaces
such as wooden floors, floor panels, parquet, marble, tiles,
etc.
Delicate and soft natural bristles ensure maximum vacuum
effectiveness and protects against scratching the cleaned
surface.
Preparing the vacuum cleaner for
operation
1 Insert the curved hose end in the opening of the vacuum
cleaner and gently press. A characteristic click indicates that
the hose has been properly installed.
2 Connect the other end of the hose (handle) with the
telescopic suction tube. In order to do so press the locking
device “A” and slide the tube into the hose handle so that
the locking device “A” is blocked in opening “B” .
3 Adjust the length of the telescopic suction tube by sliding
the slider according to the arrow and pull out/pull the tube
together.
4 Assemble the appropriate nozzle or brush to the other
end of the suction tube.
5
You may assemble a basket for picking up small objects
in the combination brush with the small item separator. In
order to do so remove the blank cover and insert the basket.
6 To clean hard surfaces – wooden floors, plastic floors,
ceramic tiles etc. pull out the brush by pressing the switch on
the combination brush according to the figure .
7 Grab the plug (7) and pull the cord out of the vacuum
cleaner.
ATTENTION! While puling out the cord pay attention
to the yellow stripe which signals the end of the
cord. Further attempts (pulling on cord) may result in
damaging the cord.
8 Plug in the appliance.
Before operation make sure that the SAFBAG bag is installed
in the vacuum cleaner chamber and that inlet filter and the
HEPA outlet filter is installed in the appliance.
9 Switch on the vacuum cleaner by pressing the “on/off”
button (2) .
10 The vacuum cleaner is equipped with an electronic
power control which allows to gradually adjust the vacuum
cleaner suction power during operation. To adjust the
suction power use the power adjustment buttons (10,12)
– to increase the suction power or – to decrease the
suction power. The suction power setting is indicated by the
appropriate number of lit diodes.
The vacuum cleaner will by default begin operation at the
medium power range. 3 diodes will light on the suction power
level indicator (11) .
The suction power may be adjusted during operation.
The recommended settings are:
Setting 1 – vacuuming curtains
Setting 2 – vacuuming upholstery
Setting 3 – cost-effective power
Setting 4 – vacuuming carpets
Setting 5 – vacuuming hard floors and crevices.
11 The vacuum cleaner type 1600.3 is additionally equipped
with remote suction power control located in the suction hose
handle. It allows to change the suction power without the
necessity to bend down.
A