![background image](http://html1.mh-extra.com/html/zelmer/ir8100/ir8100_user-manual_3403351071.webp)
71
IR8100-001_v01
To reduce the temperature press
the fabric and steam
emission selection button
„
” (every pressing is
accompanied by a sound signal). On LCD display you will
see the options displayed in opposite order than in the case
of increasing the temperature.
When one of the options from 1 to 4 is selected
(from „
” to „
”
), you
can iron in dry mode only and no steam is
generated. If you operate the iron with these
settings, you will see red pilot light.
3
The pilot light (2)
switches off automatically as soon as
the selected temperature of iron baseplate is reached.
When one of the options from 5 to 9 is selected
(from „
” to „
”), you
can use the steam while ironing.
4
When the steam boiler is being heated, on the LCD
display you will see
the steam boiler heating indicator
blinking. As soon as the appropriate temperature is
reached,
the steam boiler heating indicator
stops blinking
and shall be no longer displayed on LCD display.
5
Set
the steam emission button (3)
to the appropriate
position (
– steam is emitted from the openings placed
in the front part of the iron;
– steam is emitted from all
openings of the iron).
6
If the baseplate of the iron and steam boiler are ready to
use,
the red pilot light
disappears and
the green pilot light
switches
on.
7
The appliance is ready to use.
Filling the water
B
The appliance is equipped with an electronic
water level control system. If the level of water
is too low, the water level indicator
on the
LCD display starts to blink, and the appliance
produces a sound signal. This state will last
until the water reservoir (6) is refilled.
Switch off the appliance and pull the connector’s cord
●
plug from the socket.
1
Undo
the water reservoir catch (7)
and pull
the water
reservoir (6)
out.
2
Pull
the water inlet (5) out
.
Fill
●
the water reservoir (6)
to the MAX level marked on
the container’s side.
3
Slip
the water inlet (5)
in.
4
Place
the water reservoir (6)
in its former position.
Due to the durability of anti-calc resin and water hardness, we
recommend the exchange of
the anti-cal refill (9)
when
the
replace anti-calc refill indicator
starts to blink.
If an anti-cal refill is unavailable, it is possible
to use distilled water instead and then continue
using the appliance.
Starting the appliance
1
Connect the steam generator to proper power supply.
2
You will hear a sound signal and see all the indicators
momentarily displayed on LCD display.
3
Press
the on/off button
to start the appliance. The
LCD display reads as follows:
Setting the temperature
1
Start the appliance (see: Starting the appliance).
2
Press
the fabric and steam emission selection
button
„ ” to increase the temperature and to set the
settings related thereto, starting from „
” to
„
” (every pressing of button is accompanied
by a sound signal). On LCD display you will see options in
the following order:
Summary of Contents for IR8100
