47
2750-001_v04
Technical parameters
The type of the vacuum cleaner and the technical parameters
are indicated on the rating label. Mains protection 16 A.
Does not cause interferences with audio/video devices.
Does not require grounding
.
ZELMER vacuum cleaners meet the requirements of the
applicable norms.
The appliance is in conformity with the requirements of the
directives:
Low voltage appliance (LVD) – 2006/95/EC.
–
Electromagnetic compatibility (EMC) – 2004/108/EC.
–
Noise level: 81 dB/A.
The appliance was marked by a CE sign on the rating label.
Static electricity
In the process of vacuuming of some surfaces in areas of
low air humidity the device may become electrically charged.
It is a natural phenomenon – it does not damage the device,
and it is not considered to be a fault.
In order to minimize the phenomenon, we recommend you to:
discharge the device by touching metal items in the room
●
with the pipe,
increase air humidity in the room,
●
use widely available antistatic agents.
●
Appliance elements
A
1
Accessory compartment cover
2
Combination brush fastening
3
Plug and cord
4
Outlet filter cover
5
Cord rewind button
6
Handle
7
ON/OFF button
8
Dust bag full indicator
9
Power decrease button
10
Suction power level indicator
11
Power increase button
12
Upper cover fastening
13
Basic HEPA 12 filter (installed in the vacuum cleaner)
14
Basic filter protective mesh (installed in the vacuum
cleaner)
15
“CYKLON” dust container
16
Suction hose
17
Telescopic suction tube
18
Outlet filter HEPA H11 (installed in the vacuum cleaner)
19
Inlet filter (installed in the vacuum cleaner)
20
Inlet filter casing (installed in the vacuum cleaner)
21
SAFBAG dust bag module (with the installed SAFBAG
dust bag)
22
SAFBAG dust bag
23
Parquet brush “BNB” (type 2750.0 SP, 2750.0 ST)
Is used to clean and polish hard, scratch sensitive surfaces
such as wooden floors, floor panels, parquet, marble, tiles, etc.
Delicate and soft natural bristles ensure maximum vacuum
effectiveness and protects against scratching the cleaned
surface.
24
Combination brush with a small item separator
25
Turbobrush (type 2750.0 ST)
26
Small nozzle
27
Crevice nozzle
28
Small brush
Preparing the vacuum cleaner for
operation
The Clarris Twix vacuum cleaner has two alternative dust
collecting modules which can be selected by the user:
The bagless “CYKLON” dust container with the HEPA
–
filter – where the dust is “whirled” and deposited in the
container.
The SAFBAG dust bag module – the dust is accumulated
–
in a disposable bag with high filtration quality.
1
Insert the curved hose end in the opening of the vacuum
cleaner and gently press. A characteristic click indicates that
the hose has been properly installed.
2
Connect the other end of the hose (handle) with the
telescopic suction tube. In order to do so press the locking
device
“A”
and slide the tube into the hose handle so that
the locking device
“A”
is blocked in opening
“B”
.
3
Adjust the length of the telescopic suction tube by sliding
the slider according to the arrow and pull out/pull the tube
together.
4
Assemble the appropriate nozzle or brush to the other
end of the suction tube.
5
You may assemble a basket for picking up small objects
in the combination brush with the small item separator. In
order to do so remove the blank cover and insert the basket.
6
To clean hard surfaces – wooden floors, plastic floors,
ceramic tiles etc. pull out the brush by pressing the switch on
the combination brush according to the figure
.
7
The vacuum cleaner is equipped with an accessory
compartment. To open the compartment, lift the compartment
lid and pull it downwards.
8
Grab the plug
(3)
and pull the cord out of the vacuum
cleaner.
While pulling out the cord pay attention to the
yellow stripe which signals the end of the cord.
Further attempts (pulling on cord) may result in
damaging the cord.
9
Plug in the appliance.
Before operation make sure that the SAFBAG dust bag
module or the “CYKLON” dust container is installed in the
vacuum cleaner chamber and that all filters are installed in
the appliance.
B
