49
2750-001_v04
T
he basic HEPA (High Efficiency Particulate Air) washable
class H12 filter is located at the outlet of the cyclone filter
container. The HEPA 12 washable filter is made of a special
filtration material which enables to rinse the filter under
running water once it becomes dirty and to reuse the filter.
An outlet HEPA class H11 filter (nonwashable) is located at
the outlet of the vacuum cleaner.
The filters have a high filtration capacity; they are made of
special fibers which are able to retain almost all dust particles
greater than 0.3 micron. The H11 and H12 classes determine
the filtration effectiveness of a given filter. The HEPA H11
and H12 filter retains 95.5% of particles with the size of 0.3
micron.
Before changing the filters make sure that the vacuum
cleaner is switched off and unplugged from the mains
supply.
BASIC HEPA 12 FILTER
It is necessary to periodically clean the basic HEPA 12 filer
from fine dust fractions.
Dismantle the “CYKLON” dust container and empty the
container according to the instructions in section
(E)
.
1
Turn the basic HEPA 12 filter in the UNLOCK direction
and remove the filter.
2
Remove the protective mesh of basic filter
(14)
.
Clean the mesh and dry it thoroughly. Replace the mesh
●
if damaged.
Due to safety reasons it is prohibited to install
a moist protective mesh.
Clean the pleats of the basic HEPA 12 filter
●
(13)
. The
filter can be washed under running water. Thoroughly dry
the filter. In case of damage to the filter pleat, the filter
must be replaced with a new one.
Due to safety reasons it is prohibited to install
a moist or damaged basic HEPA 12 filter (13).
3
After cleaning and drying the protective mesh and the
basic HEPA 12 filter, install the protective mesh on the HEPA
12 filter and insert the whole unit to the “CYKLON” dust
container.
4
Press the interlock button and turn the basic HEPA 12
filter
(13)
in the LOCK direction.
Insert the “CYKLON” dust container together with the
installed basic HEPA 12 filter
(13)
into the vacuum cleaner
chamber and close the cover by pressing it until you hear
a characteristic “click” according to section
(E)
.
HEPA 11 OUTLET FILTER
1
To replace the HEPA 11 filter lift the vacuum cleaner
handle and open the accessory compartment.
2
Grab the filter cover by the fastening, firmly pull with the
thumb and lift it upwards.
3
Remove the HEPA 11 filter case and replace it with a new
one. The HEPA filter ensures an effective operation of the
vacuum cleaner for about 1 year.
4
Insert the cover so that the two protrusions in the lower
part of the cover are inserted in the openings of the vacuum
cleaner body, press the filter cover so that the rear fastenings
snap shot on the body.
INLET FILTER
Release the upper cover fastening
●
(12)
and open the
cover.
Remove the SAFBAG dust bag module/the “CYKLON”
●
dust container from the vacuum cleaner chamber.
1
Slide the inlet filter casing with the installed inlet filter
from the tracks on the back side of the vacuum cleaner
chamber.
2
Remove the inlet filter
(19)
from the inlet filter casing.
3
Place the new filter in the inlet filter casing
(20)
with the
material side directed towards the inside of the casing.
4
Slide the inlet filter casing
(20)
together with the filter in
the tracks until stop to the previous position.
Always replace a damaged inlet filter (19) with
a brand new, original one.
Insert the SAFBAG dust bag module/the “CYKLON” dust
●
container into the vacuum cleaner chamber.
Close the cover by pressing it until you hear
●
a characteristic click.
Special accessories
The following special accessories may be purchased in retail
outlets:
Zelmer turbobrush (25)
May be used with all types of ZELMER vacuum cleaners. Is
used for an effective vacuuming of carpets and fitted carpets.
While using the turbobrush follow the instruction manual.
The use of the turbobrush decidedly increases the
effectiveness of removing fibrous dirt such as: animal hair,
hair, threads etc. It is practically useful in households with
pets (cats, dogs), where removing the animal hair from the
carpets and floorings is very onerous.
End of operation cleaning and
maintenance
1
Switch off the vacuum cleaner by pressing the “on/off”
button
(7)
.
2
Unplug the appliance.
3
Wind the cord by pressing the cord rewind button
(4)
.
While doing this hold the cord to make sure it is not tangled
and the plug does not hit the vacuum cleaner housing.
4
Disconnect the telescopic tube from the nozzle or brush.
5
Disconnect the telescopic tube from the hose. In order to
remove the tube from the hose handle press the
“A”
locking
device and pull the tube in the direction of the arrow.
6
Press the two side buttons on the end of the hose and
remove the hose end from the inlet opening of the vacuum
cleaner.
H
D
F
G
