Z3 Technology EUS Z3-MVE-150 User Instructions Download

Page: 75 / 79

DOC-USR-0094-08

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

9.9

Values Appearing at the Bottom of All Tabs

Parameter

Options (default in bold)

Notes

preset

serial_menu

encoder factory default

decoder factory default

--- new preset ---

(any user-defined profiles)

The configuration file to use.

serial_menu = last value saved in interface

enc/dec factory default = factory settings

Can also add more profiles by clicking on
“new” in the User Presets tab.

New Preset Button

Click to create a new user preset.

Save Button

Click to save value that was selected.

Operating Mode

Encoder Interlaced/Progressive

Encode 1 to 3 Ch

Decoder

This selects the operating mode of the unit:

“Encoder Interlaced/Progressive” is the
default mode of operation – it can be used to
encode up to two channels.

“Encode 1 to 3 Ch” is used when it is desired
to encode a single input in three different
ways. For example, as a 1080i, D1, and CIF
stream.

“Decoder” is used to select decode mode.

Stop All

Stop encode on all channels.

Start All

Start encode on all channels.

system status:

Summary of Contents for EUS Z3-MVE-150
















































































Search results

Summary of Contents for EUS Z3-MVE-150

Reviews:

Related manuals for EUS Z3-MVE-150

Brands by name

Popular brands

Z3 Technology EUS Z3-MVE-150, User Instructions

Search results

Summary of Contents for EUS Z3-MVE-150

Reviews:

Related manuals for EUS Z3-MVE-150

Brands by name

Popular brands