Z3 Technology EUS Z3-MVE-150 User Instructions Download Page 70

Page: 70 / 79

DOC-USR-0094-08

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

(TSRTP Only)

The number of columns multiplied by the
number of rows must be less than or equal
to 100.

Authentication

(RTMP only)

Disable

Enable

Supports entering an authentication User
name and Password for RTMP. When
enabled, a “User” and “Password” text box
appear. The user then enters the
appropriate User name and Password.

User (RTMP Only)

User name to enter when “Authentication”
enabled.

Password (RTMP
Only)

Password to enter when “Authentication” is
enabled.

Channel Controls

stop

Stop current encode session.

start

Start encode session.

update

Can be used to change the bit rate without
stopping/restarting an encode session (see
Section 6.8, “Changing the Bitrate and
Frame Rate Dynamically”).

clone

Duplicate CH tab (can be used to quickly
copy CH1 values to CH2, for example).

delete

Used to delete excess tabs created by clone.

(status)

IDLE, STOPPED, RUNNING,
POLLING

Current status of the encoder. “POLLING”
indicates “start” was pressed and the
encoder is waiting for valid input data to be
detected.

Note 1: Encode Resolutions Supported:

QCIF (176x144), WQVGA (320x180), QVGA (320x240), SIF (352x240), CIF (352x288), 2-CIF (352x576),

640x360, VGA (640x480), 4-CIF (704x576), 16:9 PAL (1024x576), D1 PAL (720x576),

D1 NTSC (720x480), 720p (1280x720), XGA (1280x1024), 1080 (1920x1080)

Note 2:

If input is interlaced, the Frame Rate Divider will divide the number of fields used. This means, a

Summary of Contents for EUS Z3-MVE-150
















































































Search results

Summary of Contents for EUS Z3-MVE-150

Reviews:

Related manuals for EUS Z3-MVE-150

Brands by name

Popular brands

Z3 Technology EUS Z3-MVE-150, User Instructions

Search results

Summary of Contents for EUS Z3-MVE-150

Reviews:

Related manuals for EUS Z3-MVE-150

Brands by name

Popular brands