Z3 Technology EUS Z3-MVE-150 User Instructions Download Page 37

Page: 37 / 79

DOC-USR-0094-08

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

(9)

Click “Start All” at the bottom of any tab to start encoding. Both streams will now be able to be

received via ASI and viewed using VLC media player.

(10)

Run VLC on your PC (version used by Z3: 2.1.5)

(11)

Select Media – Open Network Stream. In the box, type “udp://@ 225.1.2.3:6000”, where

“225.1.2.3” matches the values of the computer IP address or multicast address and “6000” is the
value of “Dest Port” entered in the MPTS tab.

(12)

You will then see channel 1. To view channel 2, go to “Playback -> Program -> 2” in VLC.

Figure 35 Opening VLC for MPTS Multicast Stream

Figure 36 Viewing Channel 2 in VLC

(2) Click “Start All”

Figure 34 MPTS Tab

Select Playback -> Program -> 2

(1)

Set to desired output destinations

Summary of Contents for EUS Z3-MVE-150
















































































Search results

Summary of Contents for EUS Z3-MVE-150

Reviews:

Related manuals for EUS Z3-MVE-150

Brands by name

Popular brands

Z3 Technology EUS Z3-MVE-150, User Instructions

Search results

Summary of Contents for EUS Z3-MVE-150

Reviews:

Related manuals for EUS Z3-MVE-150

Brands by name

Popular brands