Z3 Technology EUS Z3-MVE-150 User Instructions Download Page 10

Page: 10 / 79

DOC-USR-0094-08

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

4.0

FEATURES

▪

HD resolutions up to 1920x1080, including 1080p60/50, 1080i30/25, and 720p60/50

▪

H.264 support

▪

Support for extraction from up to four sub channels of audio from SDI

▪

AAC-LC, AACH-HE v1, and AAC-HE v2 audio codecs

▪

Ability to encode two different streams from the same source

▪

Closed caption support

(EIA-608, EIA-708)

▪

Pro-MPEG Forward Error Correction support for encode and decode

▪

Inputs: HDMI, 3G-SDI, ASI (Decode)

▪

Outputs: HDMI, 3G-SDI, ASI (Encode)

▪

Interfaces to 1Gb Ethernet, USB 2.0 (x2), RS-232

▪

Outputs MPEG-2 Transport Stream, RTP, RTSP, RTMP, RTMPS, TSRTP or TS File

▪

HTTP-based configuration software for user-friendly configuration and control

▪

RS-232 serial port for technical configuration and control

▪

Operating Temperature and Humidity: 0 to 40ºC at 20-80% relative humidity (non-condensing)

▪

Storage Temperature and Humidity: -10 to 65ºC at 20-80% relative humidity (non-condensing)

▪

Measurements: 430 x 215 x 44 mm (16.93 x 8.46 x 1.72 in)

▪

Weight: 2.80 kg (6.18 lb)

4.1

Supported Input Resolutions

SDI:

1080p60, 1080p50, 1080i30, 1080i29.97, 1080i25, 720p60, 720p59.94, 720p50, 576p50,
576i25, 480i30, and 480i29.97

HDMI:

1080p60, 1080p50, 1080i30, 1080i29.97, 1080i25, 720p60, 720p59.94, 720p50, 576p50,
576i25, 480p60, 480i30, and 480i29.97

4.2

Supported Output Resolutions

HDMI:

1080p60, 1080p59.94, 1080p50, 1080i30, 1080i29.97, 1080i25, 720p60, 720p59.94,
720p50

Summary of Contents for EUS Z3-MVE-150
















































































Search results

Summary of Contents for EUS Z3-MVE-150

Reviews:

Related manuals for EUS Z3-MVE-150

Brands by name

Popular brands

Z3 Technology EUS Z3-MVE-150, User Instructions

Search results

Summary of Contents for EUS Z3-MVE-150

Reviews:

Related manuals for EUS Z3-MVE-150

Brands by name

Popular brands