Z3 Technology EUS Z3-MVE-150 User Instructions Download Page 66

Page: 66 / 79

DOC-USR-0094-08

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

along with video. Selecting “False” disables
encode of audio.

Audio Info (Entries for each of the four sub channels within the HD-SDI source)

Enable

yes (Sub Channel 1)

no (Sub Channels 2-4)

Used to select which sub channel should be
used for the audio source. Only one sub
channel can be enabled.

Codec

DSP AACLC (Sub Channels 1-4)

DSP AACHE V1

DSP AACHE V2

ARM AACLC

ARM AACLC MPEG-2

ARM AACHE

ARM AACHE V2

ARM MPEG1L2

The codec to use for audio. The bitrate
range for AACLC is 32Kbps – 384Kbps (though
staying above 64Kbps is recommended for
best results). The bitrate range for AACHE
and AACHE V2 is 32Kbps – 64Kbps.

Bitrate

12 – 384 Kbps

(320 Kbps – Sub Channel 1)

(128 Kbps – Sub Channels 2-4)

The bitrate of the audio.

Mode

Mono

Stereo

Select between stereo and mono inputs.

Source

Follow Video

HDMI1

HD-SDI (Sub Channels 1-4)

HD-SDI 1+2

HD-SDI 3+4

HD-SDI 5+6

HD-SDI 7+8

None

Where to get audio for that sub channel.

RTP Port

(RTP/RTSP Only)

0 – 9999

(8892, 8894, 8896, 8898)

If RTP format is selected, the port number
associated with that audio channel.

PID

(UDP, TSRTP, TSFILE,
MPTS & ASI Only)

0 – 999 (

120,121,122,123

)

If UDP format is selected, the PID to use for
that audio channel.

Max PTS-PCR

(UDP, TSRTP, TSFILE,

0 – 9999

(

250 - Sub Channels 1-4

)

Allows user to specify a smaller interval
than 250ms between PTS and PCR. This is

Summary of Contents for EUS Z3-MVE-150
















































































Search results

Summary of Contents for EUS Z3-MVE-150

Reviews:

Related manuals for EUS Z3-MVE-150

Brands by name

Popular brands

Z3 Technology EUS Z3-MVE-150, User Instructions

Search results

Summary of Contents for EUS Z3-MVE-150

Reviews:

Related manuals for EUS Z3-MVE-150

Brands by name

Popular brands