YSI 2900 series Operation And Maintenance Manual Download Page 97

Page: 97 / 166

7.4.2 Software

From the Help menu, touch the [Software] tab to display the Software screen.

NOTE: If 21 CFR Part 11 mode is enabled, only an Administrator can access the Software tab.

7.4.2.1 Export Configuration

Insert a flash drive and wait for the Flash Drive Inserted light to change to green.

Press [Export Config] to save the current instrument configuration to the flash drive.

NOTE: The configuration file can be imported at a later date to restore the instrument configuration.

7.4.2.2 Backup

Press [Backup] to backup the current instrument setup, database, log files, and 21 CFR 11 audit files to the flash drive.

7.4.2.3 Restore

Press [Restore] to restore a previous backup file for this analyzer from a flash drive.

7.4.2.4 Default

To default all instrument settings to the factory values, touch [Reset to Defaults].

NOTE: After resetting the instrument to default settings, the sipper must be realigned with ALL locations to

prevent sipper damage.

Summary of Contents for 2900 series







































































































































































Search results

Summary of Contents for 2900 series

Reviews:

Brands by name

Popular brands

YSI 2900 series, Operation And Maintenance Manual

Search results

Summary of Contents for 2900 series

Reviews:

Brands by name

Popular brands