manualshive.com logo in svg

YSI 2900 series, Operation And Maintenance Manual

Share
Download
YSI 2900 series Operation And Maintenance Manual Download Page 142

141 

 

 

Sample Report (Brief) 

======================== 

  Sample Results Report 

======================== 

Batch:       TestBatch-1 
Analyte:         P96_B02 

------------------------ 

3A: Ammonium 

106 mg/L 

Wed 10/04/2015 1:31:09 

======================== 

 
 

======================== 

  Sample Results Report 

======================== 

Batch:       TestBatch-1 
Analyte:         P96_B02 

------------------------ 

3B: Potassium 

193 mg/L 

Wed 10/04/2015 1:31:09 

======================== 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IB mV

 (Initial Baseline Voltage). The initial baseline voltage is 

monitored before a 

sample or calibration. The IB voltage must be stable and between -40 and 60 mV. 

NPL mV

 (Net Plateau Voltage). This is the peak voltage minus the baseline voltage. 

xNPL nA

 (cross Net Plateau Current). Net plateau current of the other sensor in the module. 

PL Slope 

(Plateau Slope). The slope is reported in mV per minute. An excessive slope can be an indicator of ISE 

problems. 

Avg

 (Average). The average PL voltage for the calibration sequence (last 3 cycles of each calibrator). 

Std Dv

 (Standard Deviation). The standard deviation of the PL voltage for the calibration sequence (last 3 cycles of each 

calibrator). Must be less than 0.2. 

->Coef

 (Selectivity Coefficient). The response of the ISE to one calibrator vs. the other calibrator. Calculated during the 

last 3 cycles of each calibrator. Must be greater than zero and less than 0.3 for ammonium; greater than zero and less 
than 0.1 for potassium. Depending on the application, the 2950 may operate with an ammonium coefficient as high as 
0.40, provided it passes the daily checks in section 5.1. However, it is the user’s responsibility to determine if operation is 
acceptable for their specific application. 

->Slp

 (Slope). The response of the ISE in mV per decade over the range of calibrator solutions. Must be greater than 52 

mV/decade. 

End Point

 is the time from dispensing the sample into the sensor module until the instrument reads the probe signal. The 

value for ISEs is 30 seconds.  

Sample Report (Detail)

 

 

 

 

======================== 

  Sample Results Report 

======================== 

Batch:             P96-1 
Analyte:         P96_B02 
------------------------ 
3A: Ammonium 

105 mg/L 

 IB mV 

20.62 

 NPL mV 

8.23 

 xNPL mV 

1.23 

PL Slope mV/m 

0.23 

Temp (C) 

25.33 

Volume (uL) 

 

25 

Dilution Factor 

x1 

Wed 10/04/2015 1:31:09 
  YSI 2950D – 15J000024 

======================== 

 
 

======================== 

  Sample Results Report 

======================== 

Batch:             P96-1 
Analyte:         P96_B02 
------------------------ 
3B:Potassium 

196 mg/L 

 IB mV 

25.83 

 NPL mV 

13.25  

 xNPL mV 

2.23 

PL Slope mV/m 

0.13 

Temp (C) 

25.33 

Volume (uL) 

 

25 

Dilution Factor 

x1 

Wed 10/04/2015 1:31:09 
  YSI 2950 – 15J000024 

======================== 

 

 

 

Summary of Contents for 2900 series







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands