manualshive.com logo in svg

YSI 2900 series, Operation And Maintenance Manual

Share
Download
YSI 2900 series Operation And Maintenance Manual Download Page 10

9 

 

3. Getting Started 

  Unpacking 

3.1

When you unpack your new 2900 Series for the first time, check the packing list to make sure you have received 
everything listed. Note that reagents for the 2900 Series are not packaged in the same carton as the instrument. If there is 
anything missing or damaged, call the dealer from whom you purchased the 2900 Series. If you do not know which of our 
authorized dealers sold the system to you, call YSI Life Sciences Customer Service at 800 659-8895 or 937 767-7241, 
and we'll be happy to help you. 

 

1.  After removing the instrument from the shipping box, tilt the display to the full upright position. 

 

Figure 3.1 

 

2.  Grasp the hand hold in the right side cover of the instrument and pull up and out to remove the cover.  

NOTE: Leave the cover off the instrument until you have aligned the sipper and installed the membranes as 
described in the following sections.

 

3.  Carefully cut the tie strap holding the sipper. 

 

Figure 3.2 

Remove tie strap 

Summary of Contents for 2900 series







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands