manualshive.com logo in svg

YSI 2900 series, Operation And Maintenance Manual

Share
Download
YSI 2900 series Operation And Maintenance Manual Download Page 130

129 

 

 

C2A 

Apply plenty of grease (included with the new pump tubing) to the longer section of new calibrator pump tubing. 

Insert the new pump tubing around the pump roller assembly and into calibrator pump C2A. Make sure the short section 
of tubing is on the left side of the pump. The tubing attached this fitting connects to the left fitting on waste module 2. 

Place a red pump head cover onto the cal pump and press until it snaps into place. 

Connect the tubing from the right side of the pump to the second fitting from the top of the top manifold. 

Connect Cal bottle tubing marked C2A to the matching fitting on the opposite side of the manifold. 

 

Figure 9.12 

C2B 

Apply plenty of grease (included with the new pump tubing) to the shorter section of new calibrator pump tubing. 

Insert the new pump tubing around the pump roller assembly and into calibrator pump C2B. Make sure the short section 
of tubing is on the left side of the pump. The tubing attached this fitting connects to the right fitting on waste module 2. 

Place a red pump head cover onto the cal pump and press until it snaps into place. 

Connect the tubing from the right side of the pump to the bottom fitting of the top manifold. 

Connect Cal bottle tubing marked C2B to the matching fitting on the opposite side of the manifold. 

C2A 

B2 

B3 

C2B 

C3A 

C3B 

B2 

C2A 

C2B 

B3 

C3A 

C3B 

C1A 

B1 

C1B 

Summary of Contents for 2900 series







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands