manualshive.com logo in svg

YSI 2900 series, Operation And Maintenance Manual

Share
Download
YSI 2900 series Operation And Maintenance Manual Download Page 133

132 

 

 

 

Unscrew the sipper cone, slide it down and remove it from the sipper. Loosen the two needle mount screws two turns, 
then remove the sipper by sliding it straight out of the mounts. 

 

 

Carefully insert the long thin end of the new sipper and slide it into the mounts. Slide the sipper cone up the sipper and 
screw it into the sipper arm. Be sure the sipper is centered in both mounts. Tighten the mount screws gently until they 
contact the sipper, then tighten an additional ¼ turn (

do not over tighten

). Connect new tubing from the Preventive 

Maintenance Kit to the new sipper. Install the sipper arm cover and secure using the hex screw (

do not over tighten

). 

Route the new sipper tubing behind the sipper assembly and connect the other end to the front connector of the sipper 
pump. 

9.4.12  Calibrate Sipper 

Align the Sipper with the sample modules as described in 4.5 Align Sipper. 

9.4.13  Install Bottles 

Temporarily place the bottle trays next to the instrument and install the bottles. Connect the tubing and cables to the 
bottles. Be sure to install new reagents in the clean bottles. 

9.4.14  Install Membranes and ISEs 

Install new membranes and ISEs as prescribed. 

9.4.15  Prime Fluid System 

Prime the buffer and calibration systems. After checking for any leaks, reinstall the pump covers on both sides of the 
instrument and slide the bottle trays into position. 

Calibrate the instrument and run the daily checks to confirm operation.

 

Summary of Contents for 2900 series







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands