manualshive.com logo in svg

YSI 2900 series, Operation And Maintenance Manual

Share
Download
YSI 2900 series Operation And Maintenance Manual Download Page 123

122 

 

Unscrew and remove the enzyme/ISE probes and the temperature probe from each sample module. Place the ISEs and 
reference electrodes in 2970 Buffer solution to prevent them from drying out. 

 

Figure 9.2 

 

Remove the sample modules. Remove and discard the small magnetic stir bar inside each module. Clean the modules 
with the appropriate disinfecting agent. 

9.4.2  Waste Module Cleaning 

Unscrew the three hex screws from the top of waste module 1. Disconnect the calibrator and waste tubing and remove 
the waste modules from the base plate. 

 

Figure 9.3 

 

Clean the waste modules with the appropriate disinfecting agent. 

Remove the o-rings from the base plate. Clean up any salt deposits or fluid on the base plate. Be sure that the base plate 
and all other parts are dry. 

9.4.3  Enzyme Probe Cleaning 

With normal use, enzyme sensors may become fouled and cease to operate normally. A fouled sensor’s output current 
will decrease and calibration may become unstable. Since the severity of fouling will vary, listed below are methods of 
cleaning which should be matched to the cleaning needs. Follow the steps carefully and in order. 

9.4.3.1  Sensor Maintenance 

It is necessary to maintenance the enzyme sensors when the PM kit is installed and periodically as needed. 

1.  Remove the enzyme Membrane and hold the probe with the electrodes facing up. 

Waste Module 

Allen Screws 

Potassium ISE 

Temperature Probe 

Reference Electrode 

Ammonium ISE 

Summary of Contents for 2900 series







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands