YOKOGAWA TC10, Engineering Manual

Page: 31 / 36

Yokogawa Electric Corporation - TC10 - ENGINEERING MANUAL - PAG. 31
no. Param. Description
Dec.
Point
Values Default
59 SELF Self tuning enabling 0
no = The instrument does not perform the self-tuning
YES = The instrument is performing the self-tuning
no
60 HSEt Hysteresis of the ON/OFF control dP 0 to 9999 (E.U.) 1
61 cPdt Time for compressor protection 0 From 0 (oFF) to 9999 (s) oFF
62 Pb Proportional band dP 1 to 9999 (E.U.) 50
63 ti Integral time 0 From 0 (oFF) to 9999 (s) 200
64 td Derivative time 0 From 0 (oFF) to 9999 (s) 50
65 Fuoc Fuzzy overshoot control 2 0.00 to 2.00 0.50
66 tcH Heating output cycle time 1 0.1 to 130.0 (s) 20.0
67 rcG
Power ratio between heating and
cooling action
2 0.01 to 99.99 1.00
68 tcc Cooling output cycle time 1 0.1 to 130.0 (s) 20.0
69 rS Manual reset (Integral pre-load) 1 -100.0 to +100.0 (%) 0.0
70 Str.t Servomotor stroke time 0 5 to 1000 seconds 60
71 db.S Servomotor dead band 0 0 to 100% 50
72 od Delay at power up 2 From 0.00 (oFF) to 99.59 (hh.mm) oFF
73 St.P
Maximum power output used during
soft start
0 -100 to 100 (%) 0
74 SSt Soft start time 2
- 0.00 (oFF);
- 0.01 to 7.59 (hh.mm);
- inF (always ON).
oFF
75 SS.tH Threshold for soft start disabling dP -1999 to +9999 (E.U.) 9999
]
SP group - Set point parameters
no. Param. Description
Dec.
Point
Values Default
76 nSP Number of used set points 0 1 to 4 1
77 SPLL Minimum set point value dP From -1999 to SPHL -1999
78 SPHL Maximum set point value dP From SPLL to 9999 9999
79 SP Set point 1 dP From SPLL to SPLH 0
80 SP 2 Set point 2 dP From SPLL to SPLH 0
81 SP 3 Set point 3 dP From SPLL to SPLH 0
82 SP 4 Set point 4 dP From SPLL to SPLH 0
83 A.SP Selection of the active set point 0 From 1 (SP 1) to nSP 1
84 SP.rt Remote set point type 0
RSP = The value coming from serial link is used as remote set point;
trin = The value will be added to the local set point selected by
A.SP and the sum becomes the operative set point;
PErc = The value will be scaled on the input range and this value
will be used as remote SP.
trin
85 SPLr Local/remote set point selection 0
Loc = local;
rEn = remote.
Loc
86 SP.u
Rate of rise for POSITIVE set point
change (ramp UP)
2 0.01 to 99.99 (inF) Eng. units per minute inF
87 SP.d
Rate of rise for NEGATIVE set point
change (ramp DOWN)
2 0.01 to 99.99 (inF) Eng. units per minute inF