Yingang YG125-30B Page 24 Manual Download

Page: 24 / 151

YG125-30B

Maintenance Manual

Inspection and adjustment

yellow line will be revealed at the crack point.

Explanation:

Unless expressly stated or indicated in the maintenance period table, check and adjust all parts of the YG125-30A

motorcycle according to the contents hereof before using it.

Technical specifications

●

Throttle bar free stroke

：

1-3mm

●

Recommended spark plug

：

CPR8EA-9

●

Spark plug gap

：

0.7-0.9mm

●

Valve clearance (cold)

）

0.06-0.08mm

●

）

0.06-0.08mm

●

Idle speed

：

1500

150

（

rpm

）

●

Cylinder pressure

：

≥

0.8MPa(300rpm)

●

Driving chain tension

：

～

20mm

●

Rear brake pedal free stroke

～

30mm

●

Front brake operating handle free stroke 10

～

20mm

●

Clutch operating handle free stroke

～

20mm

Summary of Contents for YG125-30B
























































































































































Search results

Summary of Contents for YG125-30B

Reviews:

Related manuals for YG125-30B

Brands by name

Popular brands

Yingang YG125-30B, Manual

Search results

Summary of Contents for YG125-30B

Reviews:

Related manuals for YG125-30B

Brands by name

Popular brands