Yealink One Talk W78B User Manual Download Page 38 | Manualshive

Page: 38 / 47

background image

User guide

38

Procedure

1.

Go to Menu > Basic Settings > Change PIN

2.

Enter your old and new unlock PIN respectively
The unlock PIN length must be within 15 digits

3.

Confirm the action

Locating

You can locate a misplaced registered using the base station.

Procedure

1.

Press

on the base station

All the handset that registered to this base station will ring simultaneously and the screen will display the IP address of the base station

You can press any key on handset to stop ringing (For CP930W, tap the

,

, OK key and the End Call

Note: When the handsets are not in the idle status, they will not ring simultaneously.

Renaming the handset

The handset will be named automatically if successfully registered to the base station. You can personalize the handset name.

Procedure

1.

Go to OK > Settings > Handset Name

2.

Edit the current name in the Rename/Phone Name field

3.

Confirm the action

Setting the eco mode+

Eco mode+ turns off the transmission power and the radio waves emitted are virtually zero when the phone is in standby mode.

About this task

You can enable or disable the eco mode+. If the eco mode+ is enabled, there is no signal interaction between the handset and the base station, and
the color of the signal strength indicator on the idle screen will be displayed in green. When a call arrives or a connection occurs, the phone exits
the eco mode+ automatically, and the color of the signal strength indicator on the idle screen changes from green to white.

Procedure

1.

Go to OK > Settings > System Settings > Eco Mode+

2.

Press Change

3.

Enter the system PIN (default: 0000) and then press Done. The phone prompts whether to reboot the base station

4.

Confirm the action
The base station reboots to make the change take effect. The change applies to all the handsets registered to the base station. The color of
the signal strength indicator on the idle screen will change from white to green

Setting the eco mode

Using the eco mode can greatly reduce the transmission power and signal output when the handset is during a call.

The attenuation range is 20m. When the distance between the base station and the handset is over 20m, the eco mode is disabled automatically. If
the eco mode is enabled, the radio coverage of the base station will be reduced.

Procedure

«
...
36
37
38
39
40
...
»

Summary of Contents for One Talk W78B
















































Reviews:

No comments

Related manuals for One Talk W78B

Brand: Olympia Pages: 54

Brand: Hanlong Pages: 57

Brand: Yealink Pages: 8

Brand: Qing Xin Electronic Pages: 45

Brand: TCL Pages: 61

UNIVERGE SV8100 DT7 SERIES

Brand: NEC Pages: 16

Brand: Opel mobile Pages: 76

Brand: GAI-Tronics Pages: 21

Brand: UTStarcom Pages: 72

Brand: Alcatel Pages: 22

Brand: NTT docomo Pages: 201

Aastra 9133i IP

Brand: ADTRAN Pages: 31

Brand: Allview Pages: 88

Brand: Gigaset Pages: 2

Brand: M4TEL Pages: 13

Brand: Grandstream Networks Pages: 12

Moment SPH-M900

Brand: Samsung Pages: 122

My Shot SCH-r430 series

Brand: Samsung Pages: 142

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands