YASKAWA GA800 Series, Maintenance & Troubleshooting

Page: 216 / 566

3.10 H: Terminal Functions
216 YASKAWA TOEPYAIGA8001B GA800 Drive Maintenance & Troubleshooting
Setting Value Function Description
137 !During Frequency Output
The terminal deactivates when the drive outputs frequency.
ON : The drive is not outputting frequency.
OFF : The drive is outputting frequency.
138 !Drive Enabled
This terminal deactivates when the H1-xx = 16A [Drive Enable] terminal deactivates.
139 !Watt Hour Pulse Output
Outputs the pulse that shows the watt hours.
13C !LOCAL Control Selected
The terminal deactivates when the Run command source or frequency reference source is LOCAL.
ON : REMOTE
OFF : LOCAL
13D !During Speed Search
The terminal deactivates when the drive does speed search.
13E !PID Feedback Low
The terminal deactivates when the drive detects FbL [PID Feedback Loss] .
13F !PID Feedback High
The terminal deactivates when the drive detects FbH [Excessive PID Feedback] .
14A !During KEB Ride-Thru
The terminal deactivates when the drive executes the KEB Ride-Thru function.
14B !During Short Circuit
Braking
The terminal deactivates during Short Circuit Braking.
Note:
When A1-02 = 8 [Control Method Selection = EZ Vector Control] , this function is available when you use a PM motor.
14C
!During Fast Stop
The terminal deactivates when the fast stop is in operation.
14D !oH Pre-Alarm Reduction
Limit
The terminal deactivates when L8-03 = 4 [Overheat Pre-Alarm Selection = Operate at Reduced Speed (L8-19)] and oH [Heatsink
Overheat] does not clear after the drive decreases the frequency for 10 cycles.
14E !Braking Transistor Fault (rr)
The terminal deactivates when the internal braking transistor overheats and the drive detects an rr [Dynamic Braking Transistor
Fault] fault.
14F !Braking Resistor Overheat
(rH)
The terminal deactivates when the braking resistor overheats and the drive detects an rH [Braking Resistor Overheat] fault.
160 !Internal Cooling Fan Failure
The terminal deactivates when the drive detects a cooling fan failure in the drive.
161 !RotorPositionDetection
Complete
The terminal deactivates when drive receives a Run command and the drive detects the motor magnetic pole position of the PM
motor.
162 !Modbus Reg 1 Status
Satisfied
The terminal deactivates when the bit specified by H2-07 turns on regarding the MEMOBUS register address configured with H2-
08 .
163 !Modbus Reg 2 Status
Satisfied
The terminal deactivates when the bit specified by H2-10 turns on regarding the MEMOBUS register address configured with H2-
09 .
165 !Standby Output
The terminal activated after the drive stops operating and after the time set with b8-51 [Standby Mode Wait Time] .
ON : The Run command turns off and the drive stops operating. When time set in b8-51 [Standby Mode Wait Time] is expired, the
magnetic contactor on the input side turns off.
OFF : The Run command turns on and the magnetic contactor on the input side turns on.
166 !Comparator 1
The terminal deactivates when the monitor value set with H2-20 is within range of H2-21 and H2-22 for the time set in H2-24 .
167 !Comparator 2
The terminal deactivates when the when the monitor value set with H2-26 is outside the range of H2-27 and H2-28 for the time set
in H2-30 .
169 !External Power 24V Supply
The terminal deactivates when there is an external 24V power supply between terminals PS-AC.
ON : The external 24V power supply is not supplying power.
OFF : The external 24V power supply is supplying power.
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
V/f CL-V/f OLV CLV AOLV OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV