Yamato DP-6700 Page 51 Technical Manual Download

Page: 51 / 55

YCO-201008

DP-6700

Technical Manual

Chapter 3 How to disassemble

3-14

As shown in

Figure 3-1 View of underside

, the underside of the support holder has a notch.

Pass the connector of the load cell cable and cable bush through the notch, and then remove

the cable of the load cell.

Figure 3-1 View of underside

3.3.2 Tips for installation of the load cell

The load cell is supplied in an assembly as shown in

Fig. 3-2 View of Load Cell for shipment

The load cell comes with the preassembled cable bush and connector, and accordingly the

connector can be connected without disassembling the indicator.

The connector for relaying purpose comes out of the indicator as shown in

Figure 3-3 View of

indicator Connector.

Connect this connector to that of the load cell and put it back into the

indicator. Then fasten the cable bush.

Summary of Contents for DP-6700
























































Search results

Summary of Contents for DP-6700

Reviews:

Related manuals for DP-6700

Brands by name

Popular brands

Yamato DP-6700, Technical Manual

Search results

Summary of Contents for DP-6700

Reviews:

Related manuals for DP-6700

Brands by name

Popular brands