Yamaha Stagepas 600i Service Manual Download Page 38

Page: 38 / 121

STAGEPAS 600i

3-5. JACK inspection

The connection inspection of SUBWOOFER OUT jack is
conducted.
The connection inspection of REVERB FOOT SW jack is
conducted.

[SUBWOOFER OUT]

Once the headphone jack is attached to the SUBWOOFER-
OUT terminal, click “OK” button.

The result is displayed in output window as shown below.

When Normal

LIMIT LED

PASS: LIMIT LED

SIGNAL LED

PASS: 6/+3/0/-6/-20 LED

POWER LED

PASS: POWER LED

REVERB-ON LED

PASS: REVERB-ON LED

FBS LED

PASS: FBS LED

BOOST LED

PASS: BOOST LED

LED ALL

PASS: LED ALL

When out of order

LIMIT LED

FAIL: LIMIT LED

SIGNAL LED

FAIL: 6/+3/0/-6/-20 LED

POWER LED

FAIL: POWER LED

REVERB-ON LED

FAIL: REVERB-ON LED

FBS LED

FAIL: FBS LED

BOOST LED

FAIL: BOOST LED

LED ALL

FAIL: LED ALL

Determine all LED tests comprehensively.

If result is PASS, click “Yes” button.
If result is FAIL, click “No” button.

3-5. JACK 検査

SUBWOOFER OUT 端子の接続検査を行います。
REVERB FOOT SW 端子の接続検査を行います。

[SUBWOOFER OUT]

SUBWOOFER-OUT 端子にヘッドフォンジャック
を取り付けたら、「OK」ボタンをクリックします。

検査結果はアウトプットウインドウへ下記のように
表示されます。

正常時

LIMIT LED

PASS: LIMIT LED

SIGNAL LED

PASS: 6/+3/0/-6/-20 LED

POWER LED

PASS: POWER LED

REVERB-ON LED

PASS: REVERB-ON LED

FBS LED

PASS: FBS LED

BOOST LED

PASS: BOOST LED

LED ALL

PASS: LED ALL

故障時

LIMIT LED

FAIL: LIMIT LED

SIGNAL LED

FAIL: 6/+3/0/-6/-20 LED

POWER LED

FAIL: POWER LED

REVERB-ON LED

FAIL: REVERB-ON LED

FBS LED

FAIL: FBS LED

BOOST LED

FAIL: BOOST LED

LED ALL

FAIL: LED ALL

全 LED テストの総合判定を行います。

結果が PASS の場合、「Yes」ボタンをクリックし
ます。
結果が FAIL の場合、

「No」ボタンをクリックします。

Summary of Contents for Stagepas 600i


























































































































Search results

Summary of Contents for Stagepas 600i

Reviews:

Related manuals for Stagepas 600i

Brands by name

Popular brands

Yamaha Stagepas 600i, Service Manual

Search results

Summary of Contents for Stagepas 600i

Reviews:

Related manuals for Stagepas 600i

Brands by name

Popular brands