Yamaha LZ300C Owner'S Manual Download Page 60

Page: 60 / 84

Maintenance

Checkpoints

●

Fuel system parts leakage

●

Fuel line joint leakage

●

Fuel line cracks or other damage

●

Fuel connector leakage

EMU28980

Inspecting fuel filter

WARNING

EWM00310

Gasoline is highly flammable, and its va-
pors are flammable and explosive.

●

If you have any question about properly
doing this procedure, consult your
Yamaha dealer.

●

Do not perform this procedure on a hot
or running engine. Allow the engine to
cool.

●

There will be fuel in the fuel filter. Keep
away from sparks, cigarettes, flames or
other sources of ignition.

●

This procedure will allow some fuel to
spill. Catch fuel in a rag. Wipe up any
spilled fuel immediately.

●

The fuel filter must be reassembled
carefully with the O-ring, filter cup, and
hoses in place. Improper assembly or
replacement could result in a fuel leak,
which could result in a fire or explosion

hazard.

EMU30070

Cleaning fuel filter

Loosen the filter cup ring nut.

ZMU01853

ZMU01955

1. Locking tab

ZMU01893

Summary of Contents for LZ300C





















































































Search results

Summary of Contents for LZ300C

Reviews:

Related manuals for LZ300C

Brands by name

Popular brands

Yamaha LZ300C, Owner'S Manual

Search results

Summary of Contents for LZ300C

Reviews:

Related manuals for LZ300C

Brands by name

Popular brands