Yamaha LZ300C Owner'S Manual Download Page 74 | Manualshive

Page: 74 / 84

background image

Trouble Recovery

69

EMU29670

Engine fails to operate

EMU29740

Low oil level warning activates

If the oil level is allowed to drop too low, the
red segment will appear on the oil level indi-
cator, the buzzer will sound, and engine
speed will be limited to about 2000 r/min. If
this happens, a reserve amount of oil can be
pumped from the remote oil tank to the en-
gine oil tank using the emergency switch.

WARNING

EWM01050

Be sure to stop the engine before per-

forming this procedure.

CAUTION:

ECM00900

●

If the emergency switch is held up too
long, too much oil will be pumped into
the engine oil tank, overflowing it. Re-
lease the switch when oil reaches the
upper level line on the engine oil tank.

●

Do not use this emergency procedure
unless the oil level warning indicators

are working.

1.

Remove the top cowling.

2.

Turn on the main switch.

3.

Lift the emergency switch to pump re-
serve oil into the engine oil tank from the
remote oil tank.

4.

After using the emergency switch, turn
off the main switch, then turn it back on.
This resets the warning system to nor-
mal operation. The yellow segment will
continue to be displayed on the oil level
indicator.

5.

Start the engine and return to the near-
est port for more oil.

NOTE:

●

The maximum reserve oil capacity is 1500
cm

3

(1.6 US qt, 1.31 Imp qt).

●

The oil-feed pump will not operate if the
engine is tilted up more than 35°. Put the
engine in the upright position (not tilted)

before using the emergency switch.

ON START

OFF

ZMU01906

1. Emergency switch

1. Engine oil tank
2. Remote oil tank

1

ZMU01907

1

2

ZMU01908

«
...
72
73
74
75
76
...
»

Summary of Contents for LZ300C





















































































Reviews:

No comments

Related manuals for LZ300C

Brand: J&W Pages: 28

TA870 PLUS - SETUP 2

Brand: Biostar Pages: 67

Brand: Supero Pages: 101

BaseTravel 401 S

Brand: Torqeedo Pages: 32

KEMX-1600 Series

Brand: Quanmax Pages: 74

Brand: Supermicro Pages: 100

Brand: Vector Pages: 73

Brand: Microchip Technology Pages: 35

Brand: Texas Instruments Pages: 19

P35D3 Platinum - Motherboard - ATX

Brand: MSI Pages: 104

Brand: Gigabyte Pages: 44

dsPICDEM MCHV-3

Brand: Microchip Technology Pages: 68

WAFER - E668EV ATX

Brand: IEI Technology Pages: 59

44011-0208-13-2

Brand: S&T Pages: 65

Brand: Gigabyte Pages: 88

Brand: Gigabyte Pages: 96

Brand: ASROCK Pages: 160

Brand: DFI Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands