Yamaha LZ300C Owner'S Manual Download Page 75 | Manualshive

Page: 75 / 84

background image

Trouble Recovery

70

EMU29760

Treatment of submerged motor

If the outboard motor is submerged, immedi-
ately take it to a Yamaha dealer. Otherwise
some corrosion may begin almost immedi-
ately.
If you cannot immediately take the outboard
motor to a Yamaha dealer, follow the proce-
dure below in order to minimize engine dam-
age.

EMU29970

Procedure

1.

Thoroughly wash away mud, salt, sea-
weed, and so on, with fresh water.

2.

Remove the spark plugs and face the
spark plug holes downward to allow any
water, mud, or contaminants to drain.

3.

Drain the fuel from the vapor separator,
fuel filter, and fuel line.

4.

Spray “Fogging Oil” or supply engine oil
through the intake manifold and spark

plug holes while rotating the flywheel
manually.

5.

Take the outboard motor to a Yamaha
dealer as soon as possible.

CAUTION:

ECM00400

Do not attempt to run the outboard motor

until it has been completely inspected.

ZMU01909

ZMU01910

ZMU01911

«
...
73
74
75
76
77
...
»

Summary of Contents for LZ300C





















































































Reviews:

No comments

Related manuals for LZ300C

Brand: Biostar Pages: 61

Brand: Texas Instruments Pages: 8

Brand: Gigabyte Pages: 8

Brand: AOpen Pages: 8

Brand: Rosch Computer Pages: 87

Brand: C&T Solution Pages: 84

Brand: QDI Pages: 85

Brand: Parker Pages: 56

Brand: BESTEK Pages: 13

Brand: Linear Technology Pages: 6

Brand: Broadcom Pages: 20

Brand: MSI Pages: 87

TLE986 Evalboard Series

Brand: Infineon Pages: 20

Brand: MSI Pages: 32

Brand: Acorp Pages: 74

Brand: IEI Technology Pages: 165

Brand: Texas Instruments Pages: 22

IMX233-OLX-NANO

Brand: OLIMEX Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands