Yamaha LZ300C Owner'S Manual Download Page 47 | Manualshive

Page: 47 / 84

background image

Operation

42

board motor or close the fuel cock.

3.

Press the power trim and tilt switch/
power tilt switch “

” (up) until the out-

board motor has tilted up completely.

4.

Push the tilt support knob into the clamp
bracket or pull the tilt support lever to-
ward you to support the engine.

WARNING

EWM00260

After tilting the outboard motor, be sure
to support it with the tilt support knob or
tilt support lever. Otherwise the outboard
motor could fall back down suddenly if oil
in the power trim and tilt unit loses pres-

sure.

5.

If the trim rods equipped: once the out-
board motor is supported with the tilt
support lever, press the power trim and
tilt switch “

” (down) to retract the trim

rods.

CAUTION:

ECM00250

Be sure to retract the trim rods complete-
ly during mooring. This protects the rods
from marine growth and corrosion which
could damage the power trim and tilt

mechanism.

UP

ZMU01954

ZMU01886

ZMU01884

«
...
45
46
47
48
49
...
»

Summary of Contents for LZ300C





















































































Reviews:

No comments

Related manuals for LZ300C

Brand: u-blox Pages: 25

Brand: ZiLOG Pages: 41

Brand: ASROCK Pages: 198

Brand: Gigabyte Pages: 100

Brand: Intel Pages: 12

Brand: Rosch Computer Pages: 43

Brand: ASROCK Pages: 113

Brand: TYAN Pages: 73

Brand: TYAN Pages: 81

Brand: ASROCK Pages: 57

Brand: DFI Pages: 121

Brand: Analog Devices Pages: 4

Brand: MATSONIC Pages: 52

Brand: Microsemi Pages: 19

Brand: Microsemi Pages: 6

SmartFusion UG0209

Brand: Microsemi Pages: 83

Demo Circuit 1592A

Brand: Linear Technology Pages: 9

Brand: Linear Technology Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands