Yamaha LZ300C Owner'S Manual Download Page 24

Page: 24 / 84

Basic components

EMU26460

Flushing device

This device is used to clean the cooling wa-
ter passages of the motor using a garden
hose and tap water.

NOTE:

For details on usage, see page 49.

EMU26490

Digital tachometer

The tachometer shows the engine speed
and has the following functions.

NOTE:

All segments of the display will light momen-
tarily after the main switch is turned on and

will return to normal thereafter.

EMU26550

Oil level indicator (digital type)

This indicator shows the engine oil level. If
the oil level falls below the lower limit, the
warning indicator will start to blink. For fur-
ther information, see page 26.

CAUTION:

ECM00030

Do not operate the engine without oil. Se-

rious engine damage will occur.

1. Flushing device

ZMU01951

ZMU01865

ZMU01866

1. Tachometer
2. Trim meter
3. Hour meter
4. Oil level indicator
5. Overheat warning indicator
6. Set button
7. Mode button

ZMU01891

Summary of Contents for LZ300C





















































































Search results

Summary of Contents for LZ300C

Reviews:

Related manuals for LZ300C

Brands by name

Popular brands

Yamaha LZ300C, Owner'S Manual

Search results

Summary of Contents for LZ300C

Reviews:

Related manuals for LZ300C

Brands by name

Popular brands