Yamaha LZ300C Owner'S Manual Download Page 43 | Manualshive

Page: 43 / 84

background image

Operation

38

Pull up the neutral interlock trigger (if
equipped) and move the remote control lever
quickly and firmly from neutral to forward.

EMU27781

Reverse

WARNING

EWM00190

When operating in reverse, go slowly. Do
not open the throttle more than half. Oth-
erwise the boat could become unstable,
which could result in loss of control and

an accident.

If equipped tiller control:
1.

Place the throttle grip in the fully closed
position.

2.

Move the gear shift lever quickly and
firmly from neutral to reverse.

If equipped remote control:
Pull up the neutral interlock trigger (if
equipped) and move the remote control lever
quickly and firmly from neutral to reverse.

EMU27820

Stopping engine

Before stopping the engine, first let it cool off
for a few minutes at idle or low speed. Stop-
ping the engine immediately after operating
at high speed is not recommended.

EMU27851

Procedure

1.

Turn the main switch to “

” (off).

«
...
41
42
43
44
45
...
»

Summary of Contents for LZ300C





















































































Reviews:

No comments

Related manuals for LZ300C

Brand: Ublox Pages: 2

Brand: u-blox Pages: 24

Brand: Texas Instruments Pages: 30

Brand: austriamicrosystems Pages: 8

MT9J003I12STCVH-GEVB

Brand: ON Semiconductor Pages: 5

Brand: Microsemi Pages: 15

Brand: Tews Technologies Pages: 26

Brand: Intel Pages: 110

Brand: Yamaha Pages: 114

Brand: Ublox Pages: 42

Brand: C&T Solution Pages: 65

Brand: Maxtang Pages: 13

Brand: Vector Pages: 73

Brand: Microchip Technology Pages: 35

Brand: Texas Instruments Pages: 19

Brand: Intel Pages: 62

AIMB-742 Socket 478

Brand: Intel Pages: 4

Brand: Texas Instruments Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands