Yamaha FZ6-ST Supplementary Service Manual Download Page 417

Page: 417 / 469

8-12

IGNITION SYSTEM

ELEC

EAS00752

11. Sidestand switch

Check the sidestand switch for continuity.
Refer to “CHECKING THE SWITCHES”.

Is the sidestand switch OK?

YES

Replace the side-
stand switch.

EAS00763

12. Clutch switch

Check the clutch switch for continuity.
Refer to “CHECKING THE SWITCHES”.

Is the clutch switch OK?

YES

Replace the clutch
switch.

13. Starting circuit cut-off relay (diode)

Disconnect the starting circuit cut-off relay
coupler from the wire harness.

Connect the pocket tester (

Ω

1) to the

starting circuit cut-off relay coupler as
shown.

Check the starting circuit cut-off relay for
continuity.

Positive tester probe

black / red

Negative tester probe

sky blue

EAS00753

Positive tester probe

black / red

Negative tester probe

blue / green

Continuity

Positive tester probe

sky blue

Negative tester probe

black / red

Positive tester probe

blue / green

Negative tester probe

black / red

No
continuity

YES

Replace the starting
circuit cut-off relay.

When you switch the positive and negative
tester probes, the readings in the above chart
will be reversed.

Are the tester readings correct?

NOTE:

14. Lean angle cut-off switch

Check the lean angle cut-off switch.
Refer to “FUEL INJECTION SYSTEM” in
chapter 7.

Is the lean angle cut-off switch OK?

YES

Replace the lean
angle cut-off switch.

Summary of Contents for FZ6-ST






















































































































































































































































































































































































































































































Search results

Summary of Contents for FZ6-ST

Reviews:

Related manuals for FZ6-ST

Brands by name

Popular brands

Yamaha FZ6-ST, Supplementary Service Manual

Search results

Summary of Contents for FZ6-ST

Reviews:

Related manuals for FZ6-ST

Brands by name

Popular brands