Yamaha FZ6-ST Supplementary Service Manual Download Page 318

Page: 318 / 469

5-65

CRANKCASE

ENG

EAS00399

CHECKING THE CRANKCASE

1. Thoroughly wash the crankcase halves in a

mild solvent.

2. Thoroughly clean all the gasket surfaces and

crankcase mating surfaces.

3. Check:

crankcase
Cracks / damage

Replace.

oil delivery passages
Obstruction

Blow out with compressed air.

EAS00401

CHECKING THE BEARINGS AND OIL
SEALS

1. Check:

bearings
Clean and lubricate the bearings, then rotate
the inner race with your finger.
Rough movement

Replace.

2. Check:

oil seals
Damage / wear

Replace.

CHECKING THE TIMING CHAIN

1 Check:

timing chain

Damage / stiffness

Replace the timing

chain and crankshaft sprocket as a set.

oil / water pump assembly drive chain

Damage / stiffness

Replace the oil / water

pump assembly drive chain and oil / water
pump assembly drive sprocket as a set.

ASSEMBLING THE CRANKCASE

1. Lubricate:

crankshaft journal bearings
(with the recommended lubricant)

Recommended lubricant

Engine oil

2. Apply:

sealant

Yamaha bond No. 1215

90890-85505, ACC-1109-05-01

Summary of Contents for FZ6-ST






















































































































































































































































































































































































































































































Search results

Summary of Contents for FZ6-ST

Reviews:

Related manuals for FZ6-ST

Brands by name

Popular brands

Yamaha FZ6-ST, Supplementary Service Manual

Search results

Summary of Contents for FZ6-ST

Reviews:

Related manuals for FZ6-ST

Brands by name

Popular brands