Yamaha FZ6-ST Supplementary Service Manual Download Page 384

Page: 384 / 469

7-14

Intake air pressure sensor output
voltage

3.75

4.25 V

Tester positive probe

pink / white

Tester negative probe

black / blue

When installing or removing the con-
nector, main switch turn to “OFF”.

NOTE:

FUEL INJECTION SYSTEM

Fault code No.

Symptom

Intake air pressure sensor - open or short circuit detected.

Used diagnostic code No. 03 (intake air pressure sensor)

Order

Inspection operation item and probable
cause

Operation item and countermeasure

Reinstatement
method

Connected condition of connector

Inspect the coupler for any pins that
may have pulled out.
Check the locking condition of the
coupler.

If there is a malfunction, repair it and connect it
securely.

Intake air pressure sensor coupler
Main wiring harness ECU coupler
Sub-wire harness coupler

Reinstated by
turning the
main switch
ON.

Open or short circuit in wiring harness
and / or sub lead.

Repair or replace if there is an open or short
circuit.
Between sensor coupler and ECU coupler

Black / Blue - Black / Blue
Pink / White - Pink / White
Blue - Blue

Defective intake air pressure sensor

Execute the diagnostic mode (code No. 03)
Replace if defective.
1. Connect the pocket tester (DC 20 V) to the

intake air pressure sensor coupler terminal as
shown.

2. Set the main switch to “ON”.
3. Measure the intake air pressure sensor output

voltage.

4. Is the intake air pressure sensor OK?

Summary of Contents for FZ6-ST






















































































































































































































































































































































































































































































Search results

Summary of Contents for FZ6-ST

Reviews:

Related manuals for FZ6-ST

Brands by name

Popular brands

Yamaha FZ6-ST, Supplementary Service Manual

Search results

Summary of Contents for FZ6-ST

Reviews:

Related manuals for FZ6-ST

Brands by name

Popular brands