Yamaha FZ6-ST Supplementary Service Manual Download Page 416

Page: 416 / 469

8-11

IGNITION SYSTEM

ELEC

Negative tester probe

spark plug lead

Positive tester probe

spark lug lead

Measure the secondary coil resistance.

Secondary coil resistance

18 k

Ω

at 20

C (68

Is the ignition coil OK?

YES

Replace the ignition
coil.

7. Crankshaft position sensor resistance

Disconnect the crankshaft position sensor
coupler from the wire harness.

Connect the pocket tester (

Ω

100) to the

crankshaft position sensor coupler as shown.

Positive tester probe

gray

Negative tester probe

black

Measure the crankshaft position sensor re-
sistance.

EAS00748

Crankshaft position sensor resis-
tance

248

372

Ω

at 20

C (68

(between gray and black)

Is the crankshaft position sensor OK?

YES

Replace the crank-
shaft position sen-
sor.

EAS00749

8. Main switch

Check the main switch for continuity.
Refer to “CHECKING THE SWITCHES”.

Is the main switch OK?

YES

Replace the main
switch.

EAS00750

9. Engine stop switch

Check the engine stop switch for continuity.
Refer to “CHECKING THE SWITCHES”.

Is the engine stop switch OK?

YES

Replace the right
handlebar switch.

EAS00751

10. Neutral switch

Check the neutral switch for continuity.
Refer to “CHECKING THE SWITCHES”.

Is the neutral switch OK?

YES

Replace the neutral
switch.

Summary of Contents for FZ6-ST






















































































































































































































































































































































































































































































Search results

Summary of Contents for FZ6-ST

Reviews:

Related manuals for FZ6-ST

Brands by name

Popular brands

Yamaha FZ6-ST, Supplementary Service Manual

Search results

Summary of Contents for FZ6-ST

Reviews:

Related manuals for FZ6-ST

Brands by name

Popular brands