Yamaha FZ6-ST Supplementary Service Manual Download Page 437

Page: 437 / 469

8-32

LIGHTING SYSTEM

ELEC

YES

1. License plate light bulb and socket

Check the license plate light bulb and socket
for continuity.
Refer to “CHECKING THE BULBS AND
BULB SOCKETS”.

Are the license plate light bulb and socket
OK?

Replace the license
plate light bulb, sock-
et or both.

EAS00792

2. The license plate light fails to come on.

YES

2. Voltage

Connect the pocket tester (DC 20 V) to the
license plate light coupler (wire harness light
side) as shown.

The wiring circuit
from the main switch
to the license plate
light coupler is faulty
and must be re-
paired.

Positive tester probe

blue

Negative tester probe

black

Turn the main switch to “ON”.

Measure the voltage (DC 12 V) of blue

the license plate light coupler (wire harness
side).

Is the voltage within specification?

This circuit is OK.

Summary of Contents for FZ6-ST






















































































































































































































































































































































































































































































Search results

Summary of Contents for FZ6-ST

Reviews:

Related manuals for FZ6-ST

Brands by name

Popular brands

Yamaha FZ6-ST, Supplementary Service Manual

Search results

Summary of Contents for FZ6-ST

Reviews:

Related manuals for FZ6-ST

Brands by name

Popular brands