Yamaha FZ6-ST Supplementary Service Manual Download Page 338

Page: 338 / 469

5-85

CONNECTING RODS AND PISTONS

ENG

NOTE:

24.5 Nm (2.5 m

kg, 17.7 ft

lb)

NOTE:

7. Tighten:

Install by carrying out the following procedures
in order to assemble in the most suitable condi-
tion.

connecting rod bolts.

a. Replace the connecting rod bolts with new

ones.

b. Clean the connecting rod bolts.
c. After installing the big end bearing, assemble

the connecting rod and connecting rod cap
once using a single unit of the connecting
rod.

d. Tighten the connecting rod bolt while check-

ing that the sections shown

and

are

flush with each other by touching the surface.

Side machined face

Thrusting faces (4 places at front and rear)

To install the big end bearing, care should be
taken not to install it at an angle and the position
should not be out of alignment.

e. Loosen the connecting rod bolt, remove the

connecting rod and connecting rod cap and
install these parts to the crankshaft with the
big end bearing kept in the current condition.

8. Install:

connecting rod assembly
(into the cylinder and onto the crankshaft pin)

While compressing the piston rings with one
hand, install the connecting rod assembly into
the cylinder with the other hand.

Make sure that the “Y” marks

on the con-

necting rods face towards the left side of the
crankshaft.

Summary of Contents for FZ6-ST






















































































































































































































































































































































































































































































Search results

Summary of Contents for FZ6-ST

Reviews:

Related manuals for FZ6-ST

Brands by name

Popular brands

Yamaha FZ6-ST, Supplementary Service Manual

Search results

Summary of Contents for FZ6-ST

Reviews:

Related manuals for FZ6-ST

Brands by name

Popular brands