Yamaha FZ6-ST Supplementary Service Manual Download Page 118 | Manualshive

Page: 118 / 469

background image

3-7

FUEL TANK

CHK

ADJ

4 Nm (0.4 m

S

kg, 2.9 ft

S

lb)

NOTE:

CAUTION:

NOTE:

NOTE:

INSTALLING THE FUEL PUMP

1. Install:

S

fuel pump

S

Do not damage the installation surfaces of the
fuel tank when installing the fuel pump.

S

Always use a new fuel pump gasket.

S

Install the fuel pump as shown in the illustra-
tion.

S

Tighten the fuel pump bolts in stages in a criss-
cross pattern and to the specified torque.

INSTALLING THE FUEL TANK

1. Install:

S

fuel hose

When installing the fuel hose, make sure
that it is securely connected, and that the
fuel hose holders are in the correct position,
otherwise the fuel hose will not be properly
installed.

Install the fuel hose connector securely onto the
fuel tank until a distinct “click” is heard, and then
make sure that it does not come loose.
To install the fuel hose from the fuel injection
hose, slide the cover

a

on the end of the hose in

the direction of arrow shown.

2. Install:

S

fuel sender coupler

S

fuel pump coupler

S

fuel tank breather hose (except for CAL)

S

fuel tank drain hose

There is a white paint mark on the fuel tank
breather hose (except for CAL).
Refer to “CABLE ROUTING” in chapter 2.

«
...
116
117
118
119
120
...
»

Summary of Contents for FZ6-ST






















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for FZ6-ST

Brand: Memphis Shades Pages: 2

Splendor Pro CLASSIC

Brand: HERO Pages: 56

Brand: Denali Pages: 5

Brand: hepco & becker Pages: 2

XRM125 CFT125 2020

Brand: Honda Pages: 111

80 MasterGuard (L+K)

Brand: SCHUBERTH Pages: 44

Brand: KTM Pages: 7

Brand: Xenith Pages: 7

Brand: yasuni Pages: 12

Brand: APRILIA Pages: 170

Brand: Kinroad Pages: 27

Mana GT ABS 2012

Brand: APRILIA Pages: 148

Brand: APRILIA Pages: 104

Brand: hepco & becker Pages: 2

Brand: KTM Pages: 122

Brand: KTM Pages: 33

Brand: KTM Pages: 18

Brand: KTM Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands