Yamaha F50F Owner'S Manual Download Page 40

Page: 40 / 110

Instruments and indicators

EMU26583

Overheat-alert indicator

If the engine temperature rises too high, the
alert indicator will start to blink. For further in-
formation on reading the indicator, see page
43.

NOTICE

ECM00052

Do not continue to run the engine if the
overheat-alert indicator is on. Serious en-
gine damage will occur.

EMU26602

Digital speedometer

This gauge shows the boat speed and other
information.

All segments of the display will light momen-
tarily after the main switch is turned on and
will return to normal thereafter.

EMU36061

Speedometer

The speedometer displays km/h, mph, or
knots, according to operator preference. Se-
lect the desired units of measurement by set-
ting the selector switch on the back of the
gauge. See the illustration for settings.

EMU26713

Fuel gauge

Eight segments indicate the fuel level. When

1. Low oil pressure-alert indicator

1. Overheat-alert indicator

ZMU01736

ZMU01737

1. Speedometer
2. Fuel gauge
3. Trip meter/clock/voltmeter
4. Alert indicator(s)

1. Cap
2. Selector switch (for speed unit)
3. Selector switch (for fuel sensor)

6C1-9-26-1E0.book 34 ページ２０１０年２月１０日　水曜日　午後１時５３分

Summary of Contents for F50F















































































































Search results

Summary of Contents for F50F

Reviews:

Related manuals for F50F

Brands by name

Popular brands

Yamaha F50F, Owner'S Manual

Search results

Summary of Contents for F50F

Reviews:

Related manuals for F50F

Brands by name

Popular brands