Yamaha F50F Owner'S Manual Download Page 36

Page: 36 / 110

Components

EMU26462

Flushing device

This device is used to clean the cooling wa-
ter passages of the motor using a garden
hose and tap water.

TIP:

For details on usage, see page 73.

EMU35562

Fuel filter/Water separator

This engine has a combination fuel filter/wa-
ter separator and associated alert system. If
water separated from the fuel exceeds a
specific volume, the alert device of 6Y8 Mul-
tifunction Tachometer will activate.

Activation of alert device

●

The water separator-alert indicator of 6Y8
Multifunction Tachometer will blink.

●

The buzzer will sound intermittently only
when the gear shift is in neutral.

●

If the alert system has activated, stop the
engine and consult a Yamaha dealer im-
mediately.

EMU26303

Alert indicator

If the engine develops a condition which is
cause for alert, the indicator lights up. For

1. Cowling lock lever(s)

1. Flushing device

ZMU05093

ZMU05095

ZMU07078

ZMU05474

ZMU07079

6C1-9-26-1E0.book 30 ページ２０１０年２月１０日　水曜日　午後１時５３分

Summary of Contents for F50F















































































































Search results

Summary of Contents for F50F

Reviews:

Related manuals for F50F

Brands by name

Popular brands

Yamaha F50F, Owner'S Manual

Search results

Summary of Contents for F50F

Reviews:

Related manuals for F50F

Brands by name

Popular brands