Yamaha F50F Owner'S Manual Download Page 22

Page: 22 / 110

Specifications and requirements

conform to U.S. Environmental Protection
Agency (EPA) regulations for marine SI en-
gines. See the label affixed to your engine for
details.

EMU31570

Approval label of emission control certif-
icate

This label is attached to the bottom cowling.
New Technology; (4-stroke) MFI

EMU25332

Manufactured date label

This label is attached to the clamp bracket or
the swivel bracket.

1. Approval label location

ZMU05797

ZMU06894

EMISSION CONTROL INFORMATION

MFI

THIS ENGINE CONFORMS TO CALIFORNIA AND U.S. EPA EXHAUST
REGULATIONS FOR SI MARINE ENGINES. REFER TO THE OWNER'S
MANUAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS.
MEETS U.S. EPA EVAP STANDARDS USING CERTIFIED COMPONENTS.

FAMILY:
DISPLACEMENT: liters
SPARK PLUG:
FUEL: GASOLINE

FELs(HC+NOx / CO): / g/kW-hr MAX POWER: kW
IDLE SPEED: ± rpm IN NETRAL
SPARK PLUG GAP (mm):
VALVE LASH (mm) IN: EX:

YAMAHA MOTOR CO.,LTD.

1. Manufactured date label location

ZMU04701

6C1-9-26-1E0.book 16 ページ２０１０年２月１０日　水曜日　午後１時５３分

Summary of Contents for F50F















































































































Search results

Summary of Contents for F50F

Reviews:

Related manuals for F50F

Brands by name

Popular brands

Yamaha F50F, Owner'S Manual

Search results

Summary of Contents for F50F

Reviews:

Related manuals for F50F

Brands by name

Popular brands